- 您现在的位置：买卖IC网 > PDF目录44993 > LTC3788IGN-1#PBF (LINEAR TECHNOLOGY CORP) DUAL SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO28 PDF资料下载
参数资料
| 型号： | LTC3788IGN-1#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | DUAL SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | 0.150 INCH, LEAD FREE, PLASTIC, SSOP-28 |
| 文件页数： | 7/30页 |
| 文件大小： | 384K |
| 代理商： | LTC3788IGN-1#PBF |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC3788-1
15
37881fb
applicaTions inForMaTion
Sense Resistor Current Sensing
A typical sensing circuit using a discrete resistor is shown
in Figure 2a. RSENSE is chosen based on the required
output current.
The current comparator has a maximum threshold
VSENSE(MAX). The current comparator threshold sets the
peak of the inductor current, yielding a maximum average
output current, IMAX, equal to the peak value less half the
peak-to-peak ripple current, IL. To calculate the sense
resistor value, use the equation:
RSENSE =
VSENSE(MAX)
IMAX +
IL
2
When using the controller in low VIN and very high voltage
output applications, the maximum output current level will
be reduced due to the internal compensation required to
meet stability criterion for boost regulators operating at
greater than 50% duty factor. A curve is provided in the
Typical Performance Characteristics section to estimate
this reduction in peak output current level depending upon
the operating duty factor.
Inductor DCR Sensing
For applications requiring the highest possible efficiency
at high load currents, the LTC3788-1 is capable of sensing
the voltage drop across the inductor DCR, as shown in
Figure 2b. The DCR of the inductor can be less than 1mΩ
for high current inductors. In a high current application
requiring such an inductor, conduction loss through a
sense resistor could reduce the efficiency by a few percent
compared to DCR sensing.
If the external R1||R2 C1 time constant is chosen to be
exactly equal to the L/DCR time constant, the voltage drop
across the external capacitor is equal to the drop across
theinductorDCRmultipliedbyR2/(R1+R2).R2scalesthe
voltage across the sense terminals for applications where
the DCR is greater than the target sense resistor value.
To properly dimension the external filter components, the
DCR of the inductor must be known. It can be measured
using a good RLC meter, but the DCR tolerance is not
always the same and varies with temperature. Consult
the manufacturer’s data sheets for detailed information.
Using the inductor ripple current value from the inductor
valuecalculationsection,thetargetsenseresistorvalueis:
RSENSE(EQUIV) =
VSENSE(MAX)
IMAX +
IL
2
To ensure that the application will deliver full load current
over the full operating temperature range, choose the
minimum value for the maximum current sense threshold
(VSENSE(MAX)).
Next, determine the DCR of the inductor. Where provided,
use the manufacturer’s maximum value, usually given at
20°C. Increase this value to account for the temperature
coefficientofresistance,whichisapproximately0.4%/°C.A
conservativevalueforthemaximuminductortemperature
(TL(MAX)) is 100°C.
To scale the maximum inductor DCR to the desired sense
resistor value, use the divider ratio:
RD =
RSENSE(EQUIV)
DCRMAX at TL(MAX)
C1 is usually selected to be in the range of 0.1F to 0.47F.
This forces R1|| R2 to around 2k, reducing error that might
have been caused by the SENSE+ pin’s ±1A current.
The equivalent resistance R1|| R2 is scaled to the room
temperature inductance and maximum DCR:
R1||R2
=
L
(DCR at 20
°C) C1
The sense resistor values are:
R1
=
R1||R2
RD
; R2
=
R1RD
1
RD
The maximum power loss in R1 is related to duty cycle,
and will occur in continuous mode at VIN = 1/2 VOUT:
PLOSS R1=
(VOUT VIN) VIN
R1
Ensure that R1 has a power rating higher than this value.
If high efficiency is necessary at light loads, consider this
power loss when deciding whether to use DCR sensing or
sense resistors. Light load power loss can be modestly
higher with a DCR network than with a sense resistor,
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3788EGN-1#TRPBF | DUAL SWITCHING CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3789EGN#TRPBF | 0.1 A SWITCHING CONTROLLER, 710 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3789EUFD#TRPBF | 0.1 A SWITCHING CONTROLLER, 710 kHz SWITCHING FREQ-MAX, PQCC28 |
| LTC3789EGN#PBF | 0.1 A SWITCHING CONTROLLER, 710 kHz SWITCHING FREQ-MAX, PDSO28 |
| LTC3789IUFD#PBF | 0.1 A SWITCHING CONTROLLER, 710 kHz SWITCHING FREQ-MAX, PQCC28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3788IUH#PBF | 功能描述:IC REG CTRLR BST PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3788IUH#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3789EGN#PBF | 功能描述:IC REG CTRLR BST PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3789EGN#PBF | 制造商:Linear Technology 功能描述:IC DC-DC CONV 600kHz SSOP28 |
| LTC3789EGN#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 28-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
发布紧急采购，3分钟左右您将得到回复。