- 您现在的位置：买卖IC网 > PDF目录80172 > LTC3805MPMSE#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO10 PDF资料下载
参数资料
| 型号： | LTC3805MPMSE#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封装： | LEAD FREE, PLASTIC, MSOP-10 |
| 文件页数： | 2/20页 |
| 文件大小： | 248K |
| 代理商： | LTC3805MPMSE#TRPBF |
LTC3805
10
3805ff
OPERATION
First, consider operation without overcurrent protection.
For some maximum converter output current, the voltage
ontheITHpinrisestoandisclampedatapproximately1.9V.
This corresponds to a 100mV limit on the voltage at the
ISENSE pin. As the output current is further increased, the
duty cycle is reduced as the output voltage sags. However,
the peak current in the external MOSFET is limited by the
100mV threshold at the ISENSE pin.
As the output current is increased further, eventually,
the duty cycle is reduced to the 6% minimum. Since the
external MOSFET is always turned on for this minimum
amount of time, the current comparator no longer limits
the current through the external MOSFET based on the
100mV threshold. If the output current continues to in-
crease, the current through the MOSFET could rise to a
level that would damage the converter.
To prevent damage, the overcurrent pin, OC, is also
connected to the current sense resistor, and a fault is
triggered if the voltage on the OC pin exceeds 100mV. To
protect itself, the converter stops operating as described
in the next section. External resistors can be used to ad-
just the overcurrent threshold to voltages higher or lower
than 100mV as described in the Applications Information
section.
Soft-Start and Fault Timeout Operation
The soft-start and fault timeout of the LTC3805 uses either
a fixed internal timer or an external timer programmed
by a capacitor from the SSFLT pin to GND. The internal
soft-start and fault timeout times are minimums and can
be increased by placing a capacitor from the SSFLT pin
to GND. Operation is shown in Figure 1.
Leave the SSFLT pin open to use the internal soft-start and
fault timeout. The internal soft-start is complete in about
1.8ms. In the event of an overcurrent as detected by the
OC pin exceeding 100mV, the LTC3805 shuts down and
an internal timing circuit waits for a fault timeout of about
4.25ms and then restarts the converter.
Add a capacitor CSS from the SSFLT pin to GND to increase
both the soft-start time and the time for fault timeout. Dur-
ing soft-start, CSS is charged with a 6A current. When
the LTC3805 comes out of shutdown, the LTC3805 quickly
charges CSS to about 0.7V at which point GATE begins
switching.Fromthatpoint,GATEcontinuesswitchingwith
increasing duty cycle until the SSFLT pin reaches about
2.25V at which point soft-start is over and closed-loop
regulation begins. The voltage on the SSFLT pin addition-
ally further charges to about 4.75V.
CSS also performs the timeout function in the event of a
fault. After a fault, CSS is slowly discharged from about
4.75V to about 0.7V by a 2A current. When the voltage
on the SSFLT pin reaches 0.7V the converter attempts to
restart.Moredetailonprogrammingtheexternalsoft-start
fault timeout is described in the Applications Information
section.
Powering the LTC3805
A built-in shunt regulator from the VCC pin to GND limits
the voltage on the VCC pin to approximately 9.5V as long
as the shunt regulator is not forced to sink more than
25mA. The shunt regulator is always active, even when
the LTC3805 is in shutdown, since it serves the vital func-
tion of protecting the VCC pin from overvoltage. The shunt
regulator permits the use of a wide variety of powering
schemes for the LTC3805 even from high voltage sources
that exceed the LTC3805’s absolute maximum ratings.
Further details on powering schemes are described in the
Applications Information section.
Adjustable Slope Compensation
The LTC3805 injects a 10A peak current ramp out of
its ISENSE pin which can be used, in conjunction with an
external resistor, for slope compensation in designs that
require it. This current ramp is approximately linear and
begins at zero current at 6% duty cycle, reaching peak
current at 80% duty cycle. Additional details are provided
in the Applications Information section.
相关PDF资料 |
PDF描述 |
|---|---|
| LM4040BIM3-5.0T&R | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, PDSO3 |
| LRB5D | 2-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| LRB9S | 1-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| LRC24D | 2-OUTPUT 5 W DC-DC REG PWR SUPPLY MODULE |
| LH1601-2RD8 | 1-OUTPUT 70 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3806EDE | 功能描述:IC REG CTRLR FLYBACK PWM 12-DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3806EDE#PBF | 功能描述:IC REG CTRLR FLYBACK PWM 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3806EDE#TR | 功能描述:IC REG CTRLR FLYBACK PWM 12-DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3806EDE#TRPBF | 功能描述:IC REG CTRLR FLYBACK PWM 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3808EDE | 制造商:Linear Technology 功能描述:DC DC Cntrlr Single-OUT Sync Step Down 2.75V to 9.8V Input 14-Pin DFN EP |
发布紧急采购，3分钟左右您将得到回复。