参数资料
型号: LTC3829EUHF#TRPBF
厂商: Linear Technology
文件页数: 13/40页
文件大小: 0K
描述: IC REG CTRLR BUCK PWM CM 38-QFN
标准包装: 2,500
系列: PolyPhase®
PWM 型: 电流模式
输出数: 1
频率 - 最大: 850kHz
占空比: 94%
电源电压: 4.5 V ~ 38 V
降压:
升压:
回扫:
反相:
倍增器:
除法器:
Cuk:
隔离:
工作温度: -40°C ~ 125°C
封装/外壳: 38-WFQFN 裸露焊盘
包装: 带卷 (TR)
LTC3829
OPERATION (Refer to Functional Diagram)
A phase-locked loop (PLL) is available on the LTC3829
to synchronize the internal oscillator to an external clock
source that is connected to the PLLIN pin. The PLL loop
filter network is integrated inside the LTC3829. The phase-
locked loop is capable of locking any frequency within
the range of 250kHz to 770kHz. The frequency setting
resistor should always be present to set the controller’s
initial switching frequency before locking to the external
clock. The controller is operating in forced continuous
mode when it is synchronized.
Sensing the Output Voltage with a
Differential Amplifier
The LTC3829 includes a low offset, unity-gain, high band-
width differential amplifier for applications that require true
remote sensing. Sensing the load across the load capaci-
tors directly greatly benefits regulation in high current, low
voltage applications, where board interconnection losses
can be a significant portion of the total error budget.
The LTC3829 differential amplifier has a typical output slew
rate of 2V/μs. The amplifier is configured for unity gain,
meaning that the difference between DIFFP and DIFFN is
translated to DIFFOUT, relative to SGND.
Care should be taken to route the DIFFP and DIFFN PCB
traces parallel to each other all the way to the terminals
of the output capacitor or remote sensing points on the
board. In addition, avoid routing these sensitive traces
near any high speed switching nodes in the circuit. Ideally,
the DIFFP and DIFFN traces should be shielded by a low
impedance ground plane to maintain signal integrity.
The maximum output voltage when using the differential
amplifier is INTV CC – 1.4V (typically 3.6V). Above this output
voltage the differential amplifier should not be used.
Power Good (PGOOD Pin)
The PGOOD pin is connected to an open drain of an
internal N-channel MOSFET. The MOSFET turns on and
pulls the PGOOD pin low when the V FB pin voltage is not
within ±10% of the 0.6V reference voltage. The PGOOD
pin is also pulled low when the RUN pin is below 1.22V or
when the LTC3829 is in the soft-start or tracking phase.
When the V FB pin voltage is within the ±10% regulation
window, the MOSFET is turned off and the pin is allowed
to be pulled up by an external resistor to a source of up
to 6V. The PGOOD pin will flag power good immediately
when the V FB pin is within the regulation window. However,
there is an internal 100μs power-bad mask when the V FB
goes out of the window.
Output Overvoltage Protection
An overvoltage comparator, OV, guards against transient
overshoots (>10%) as well as other more serious condi-
tions that may overvoltage the output. In such cases, the
top MOSFET is turned off and the bottom MOSFET is turned
on until the overvoltage condition is cleared.
Undervoltage Lockout
The LTC3829 has two functions that help protect the
controller in case of undervoltage conditions. A precision
UVLO comparator constantly monitors the INTV CC voltage
to ensure that an adequate gate-drive voltage is present. It
locks out the switching action when INTV CC is below 3.3V.
To prevent oscillation when there is a disturbance on the
INTV CC , the UVLO comparator has 600mV of precision
hysteresis.
Another way to detect an undervoltage condition is to moni-
tor the V IN supply. Because the RUN pin has a precision
turn-on reference of 1.22V, one can use a resistor divider
to V IN to turn on the IC when V IN is high enough. An extra
4.5μA of current flows out of the RUN pin once the RUN
pin voltage passes 1.22V. The RUN comparator itself has
about 80mV of hysteresis. One can program additional
hysteresis for the RUN comparator by adjusting the val-
ues of the resistive divider. For accurate V IN undervoltage
detection, V IN needs to be higher than 4.5V.
3829fa
For more information www.linear.com/LTC3829
13
相关PDF资料
PDF描述
GBM43DTMN CONN EDGECARD 86POS R/A .156 SLD
RLB9012-561KL INDUCTOR HI CURRENT RADIAL 560UH
LTC3862IUH#TRPBF IC REG CTRLR BST PWM CM 24-QFN
GBM43DTMD CONN EDGECARD 86POS R/A .156 SLD
RLB9012-471KL INDUCTOR HI CURRENT RADIAL 470UH
相关代理商/技术参数
参数描述
LTC3829IFE#PBF 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3829IFE#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 38TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3829IUHF#PBF 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3829IUHF#TRPBF 功能描述:IC REG CTRLR BUCK PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:PolyPhase® 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX
LTC3830-1ES8 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP(0.173",4.40mm 宽) 包装:带卷 (TR)