- 您现在的位置：买卖IC网 > PDF目录15252 > LTC3859EFE#TRPBF (Linear Technology)IC REG CTRLR BST PWM CM 38-TSSOP PDF资料下载
参数资料
| 型号： | LTC3859EFE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/42页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM CM 38-TSSOP |
| 标准包装： | 2,000 |
| PWM 型： | 电流模式，Burst Mode? |
| 输出数： | 3 |
| 频率 - 最大： | 850kHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 38-TFSOP （0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
LTC3859
OPERATION
the 0.8V internal reference for the bucks and the 1.2V
internal reference for the boost, the LTC3859 regulates the
V FB voltage to the TRACK/SS pin voltage instead of the
corresponding reference voltage. This allows the TRACK/SS
pin to be used to program a soft-start by connecting an
external capacitor from the TRACK/SS pin to SGND. An
internal 1μA pull-up current charges this capacitor creating
a voltage ramp on the TRACK/SS pin. As the TRACK/SS
voltage rises linearly from 0V to 0.8V/1.2V (and beyond
up to INTV CC ), the output voltage V OUT rises smoothly
from zero to its ?nal value.
Alternatively the TRACK/SS pins for buck channels 1 and 2
can be used to cause the start-up of V OUT to track that of
another supply. Typically, this requires connecting to the
TRACK/SS pin an external resistor divider from the other sup-
ply to ground (see the Applications Information section).
Light Load Current Operation (Burst Mode Operation,
Pulse-Skipping, or Continuous Conduction)
(PLLIN/MODE Pin)
The LTC3859 can be enabled to enter high ef?ciency Burst
Mode operation, constant frequency pulse-skipping mode
or forced continuous conduction mode at low load cur-
rents. To select Burst Mode operation, tie the PLLIN/ MODE
pin to ground. To select forced continuous operation, tie
the PLLIN/MODE pin to INTV CC . To select pulse-skipping
mode, tie the PLLIN/MODE pin to a DC voltage greater
than 1.2V and less than INTV CC – 1.3V.
When a controller is enabled for Burst Mode operation, the
minimum peak current in the inductor is set to approxi-
mately 25% of the maximum sense voltage (30% for the
boost) even though the voltage on the I TH pin indicates a
lower value. If the average inductor current is higher than
the load current, the error ampli?er EA will decrease the
voltage on the I TH pin. When the I TH voltage drops below
0.425V, the internal sleep signal goes high (enabling sleep
mode) and both external MOSFETs are turned off. The I TH
pin is then disconnected from the output of the EA and
parked at 0.450V.
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current that the LTC3859 draws. If
one channel is in sleep mode and the other two are shut
down, the LTC3859 draws only 55μA of quiescent current. If
two channels are in sleep mode and the other shut down, it
draws only 65μA of quiescent current. If all three controllers
are enabled in sleep mode, the LTC3859 draws only 80μA
of quiescent. In sleep mode, the load current is supplied by
the output capacitor. As the output voltage decreases, the
EA’s output begins to rise. When the output voltage drops
enough, the I TH pin is reconnected to the output of the
EA, the sleep signal goes low, and the controller resumes
normal operation by turning on the top external MOSFET
on the next cycle of the internal oscillator.
When a controller is enabled for Burst Mode operation,
the inductor current is not allowed to reverse. The reverse
current comparator (IR) turns off the bottom external
MOSFET (the top external MOSFET for the boost) just
before the inductor current reaches zero, preventing it
from reversing and going negative. Thus, the controller
operates in discontinuous operation.
In forced continuous operation or clocked by an external
clock source to use the phase-locked loop (see the Fre-
quency Selection and Phase-Locked Loop section), the
inductor current is allowed to reverse at light loads or
under large transient conditions. The peak inductor cur-
rent is determined by the voltage on the I TH pin, just as
in normal operation. In this mode, the ef?ciency at light
loads is lower than in Burst Mode operation. However,
continuous operation has the advantage of lower output
voltage ripple and less interference to audio circuitry. In
forced continuous mode, the output ripple is independent
of load current.
When the PLLIN/MODE pin is connected for pulse-skip-
ping mode, the LTC3859 operates in PWM pulse-skipping
mode at light loads. In this mode, constant frequency
operation is maintained down to approximately 1% of
designed maximum output current. At very light loads, the
current comparator ICMP may remain tripped for several
cycles and force the external top MOSFET to stay off for
the same number of cycles (i.e., skipping pulses). The
inductor current is not allowed to reverse (discontinuous
operation). This mode, like forced continuous operation,
exhibits low output ripple as well as low audio noise and
reduced RF interference as compared to Burst Mode
operation. It provides higher low current ef?ciency than
forced continuous mode, but not nearly as high as Burst
Mode operation.
3859fa
16
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1698IGN#TR | IC REG CTRLR ISO PWM CM 16-SSOP |
| VE-27Y-EW-F4 | CONVERTER MOD DC/DC 3.3V 66W |
| LTC1922IN-1#PBF | IC REG CTRLR ISO PWM CM/VM 20DIP |
| EEC44DREI-S93 | CONN EDGECARD 88POS .100 EYELET |
| LTC1922IN-1 | IC REG CTRLR ISO PWM CM/VM 20DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3859EUHF#PBF | 功能描述:IC REG CTRLR BST PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LTC3859EUHF#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3859IFE#PBF | 功能描述:IC REG CTRLR BST PWM CM 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3859IFE#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,500 系列:PowerWise® PWM 型:控制器 输出数:1 频率 - 最大:1MHz 占空比:95% 电源电压:2.8 V ~ 5.5 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:6-WDFN 裸露焊盘 包装:带卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名称:LM1771SSDX |
| LTC3859IUHF#PBF | 功能描述:IC REG CTRLR BST PWM CM 38VQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。