- 您现在的位置：买卖IC网 > PDF目录15308 > LTC3865IUH#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 32-QFN PDF资料下载
参数资料
| 型号： | LTC3865IUH#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/38页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 32-QFN |
| 标准包装： | 73 |
| 系列： | PolyPhase® |
| PWM 型： | 电流模式 |
| 输出数： | 2 |
| 频率 - 最大： | 880kHz |
| 占空比： | 95% |
| 电源电压： | 4.5 V ~ 38 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
LTC3865/LTC3865-1
PIN FUNCTIONS
(QFN/TSSOP)
V OSENSE1 , V OSENSE2 (Pins 1, 8/Pins 5, 13): When the
internal programmable resistive divider is used, these
pins must be connected to their corresponding outputs.
When an external resistive divider is used, these pins are
used for error ampli?er feedback inputs. They receive
the remotely sensed feedback voltages for each channel
directly from the outputs or from the external divider
across the outputs.
TK/SS1, TK/SS2 (Pins 2, 7/Pins 6, 12): Output Voltage
Tracking and Soft-Start Inputs. When one channel is
con?gured to be master of the two channels, a capacitor
to ground at this pin sets the ramp rate for the master
channel’s output voltage. When a channel is con?gured
to be the slave of the two channels, the output voltage
ramp of the master channel can be reproduced by a re-
sistor divider and applied to this pin of the slave channel.
Internal soft-start currents of 1.3μA charge the soft-start
capacitors.
I TH1 , I TH2 (Pins 3, 6/Pins 7, 11): Current Control Thresholds
and Error Ampli?er Compensation Points. Each associated
channels’ current comparator tripping threshold increases
with its I TH control voltage.
VID11, VID12, VID21, VID22 (Pins 4, 5, 12, 28/ Pins 9,
10, 18, 37): VID Inputs for Output Voltage Programming.
Tie these pins to INTV CC , GND or leave them ?oating to
set the output voltages.
I LIM (Pin 13/Pin 19) (LTC3865 Only): Current Compara-
tor Sense Voltage Range Inputs. This pin can be tied to
SGND, FLOAT or INTV CC to set the maximum current
sense threshold for each comparator. Current compara-
tor sense voltage range of the LTC3865-1 is set to default
value of 50mV.
PGOOD (Pin 14 LTC3865/NA): Co-Bonded Power Good
Indicator Output for LTC3865 in QFN Package. Open-drain
logic output that is pulled to ground when either channel
output exceeds ±10% regulation window, after the internal
20μs power bad mask timer expires.
PGOOD1, PGOOD2 (Pins 14, 13 LTC3865-1/Pins 21, 20):
Separate Power Good Indicator Outputs for LTC3865-1 in
QFN package and LTC3865 in FE package. Open-drain logic
output that is pulled to ground when the corresponding
channel output exceeds ±10% regulation window, after
the internal 20μs power bad mask timer expires.
PGND (Pin 18/NA): Power Ground Pin. Connect this pin
closely to the sources of the bottom N-channel MOSFETs,
the (–) terminal of C VCC and the (–) terminal of C IN .
EXTV CC (Pin 20/Pin 28): External Power Input to an Inter-
nal Switch Connected to INTV CC . This switch closes and
supplies the IC power, bypassing the internal low dropout
regulator, whenever EXTV CC is higher than 4.7V. Do not
exceed 6V on this pin.
INTV CC (Pin 21/Pin 29): Internal 5V Regulator Output. The
control circuits are powered from this voltage. Decouple
this pin to PGND with a minimum of 4.7μF low ESR tan-
talum or ceramic capacitor.
V IN (Pin 22/Pin 30): Main Input Supply. Decouple this pin
to PGND with a capacitor (0.1μF to 1μF).
BG1, BG2 (Pins 23, 19/Pin 31, 27): Bottom Gate Driver
Outputs. These pins drive the gates of the bottom N-chan-
nel MOSFETs between PGND and INTV CC .
BOOST1, BOOST2 (Pins 24, 17/Pins 33, 25): Boosted
Floating Driver Supplies. The (+) terminal of the booststrap
capacitors connect to these pins. These pins swing from a
diode voltage drop below INTV CC up to V IN + INTV CC .
TG1, TG2 (Pins 25, 16/Pins 34, 23): Top Gate Driver
Outputs. These are the outputs of ?oating drivers with
a voltage swing equal to INTV CC superimposed on the
switch nodes voltages.
SW1, SW2 (Pins 26, 15/Pins 35, 22): Switch Node
Connections to Inductors. Voltage swing at these pins
is from a Schottky diode (external) voltage drop below
ground to V IN .
3865fb
9
相关PDF资料 |
PDF描述 |
|---|---|
| ADM2914-1SRQZEP-R7 | IC VOLT SUP QUAD UV/OV 16QSOP |
| UPJ1K331MHD | CAP ALUM 330UF 80V 20% RADIAL |
| LTC3868IUFD-1#PBF | IC REG CTRLR BUCK PWM CM 28-QFN |
| LT1952EGN-1#TRPBF | IC REG CTRLR ISO PWM CM 16-SSOP |
| SRP1235-R22M | INDUCTOR 220NH 38.5A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3866EFE#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,000 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:1MHz 占空比:50% 电源电压:9 V ~ 10 V 降压:无 升压:是 回扫:是 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 包装:带卷 (TR) |
| LTC3866EFE#PBF | 制造商:Linear Technology 功能描述:BUCK REGULATOR CURRENT MODE SYNC TSSOP |
| LTC3866EFE#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3866EUF#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
| LTC3866EUF#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:2,500 系列:- PWM 型:电流模式 输出数:1 频率 - 最大:500kHz 占空比:96% 电源电压:4 V ~ 36 V 降压:无 升压:是 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 125°C 封装/外壳:24-WQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。