- 您现在的位置：买卖IC网 > PDF目录16037 > LTC4002ES8-8.4 (Linear Technology)IC BATT CHARGER SW LI-ION 8SOIC PDF资料下载
参数资料
| 型号： | LTC4002ES8-8.4 |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER SW LI-ION 8SOIC |
| 标准包装： | 100 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 8.9 V ~ 22 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
LTC4002
OPERATIO
mode, dropping I CC to 10 μ A. This will greatly reduce the
current drain on the battery and increase the standby time.
A 10k ? NTC (negative temperature coefficient) thermistor
can be connected from the NTC pin to ground for battery
APPLICATIO S I FOR ATIO
Undervoltage Lockout (UVLO)
An undervoltage lockout circuit monitors the input voltage
and keeps the charger off until V CC rises above the UVLO
threshold (4.2V for the 4.2 version, 7.5V for the 8.4
version) and at least 250mV above the battery voltage. To
prevent oscillation around the threshold voltage, the UVLO
circuit has 200mV per cell of built-in hysteresis. When
specifying minimum input voltage requirements, the volt-
age drop across the input blocking diode must be added
to the minimum V CC supply voltage specification.
Trickle Charge and Defective Battery Detection
At the beginning of a charge cycle, if the battery voltage is
below the trickle charge threshold, the charger goes into
trickle charge mode with the charge current reduced to
temperature qualification. The charge cycle is suspended
when the temperature is outside of the 0 ° C to 50 ° C
window (with DALE NTHS-1206N02).
CHRG Status Output Pin
When a charge cycle starts, the CHRG pin is pulled to
ground by an internal N-channel MOSFET which is capable
of driving an LED. When the charge current drops below
the End-of-Charge threshold for more than 120 μ s, the
N-channel MOSFET turns off and a weak 25 μ A current
source to ground is connected to the CHRG pin. This weak
25 μ A pull-down remains until the timer ends the charge
cycle, or the charger is in manual shutdown or sleep mode.
After a time out occurs (charge cycle ends), the pin will
become high impedance. By using two different value re-
sistors, a microprocessor can detect three states from this
pin (charging, end-of-charge and charging stopped) see
Figure 1.
10% of the full-scale current. If the low-battery voltage
persists for 30 minutes, the battery is considered defec-
V CC
V DD
tive, the charge cycle is terminated and the CHRG pin is
forced high impedance.
Shutdown
LTC4002
CHRG
390k
2k
μ PROCESSOR
OUT
IN
4002 F02
The LTC4002 can be shut down by pulling the COMP pin
to ground which pulls the GATE pin high turning off the
external P-channel MOSFET. When the COMP pin is re-
leased, the internal timer is reset and a new charge cycle
starts. In shutdown, the output of the CHRG pin is high
impedance and the quiescent current remains at 3mA.
Removing the input power supply will put the charger
into sleep mode. If the voltage at the V CC pin drops below
(V BAT + 250mV) or below the UVLO level, the LTC4002
goes into a low current (I CC = 10 μ A) sleep mode, reducing
the battery drain current.
Figure 1. Microprocessor Interface
To detect the charge mode, force the digital output pin,
OUT, high and measure the voltage at the CHRG pin. The
N-channel MOSFET will pull the pin low even with a 2k
pull-up resistor. Once the charge current drops below the
End-of-Charge threshold, the N-channel MOSFET is turned
off and a 25 μ A current source is connected to the CHRG
pin. The IN pin will then be pulled high by the 2k resistor
connected to OUT. Now force the OUT pin into a high
4002f
11
相关PDF资料 |
PDF描述 |
|---|---|
| M3TEK-4018R | IDC CABLE - MSD40K/MC40M/MCE40K |
| M3DFK-4018R | IDC CABLE - MKR40K/MC40M/MCF40K |
| M3DGK-4018R | IDC CABLE - MKR40K/MC40M/MCS40K |
| M3DEK-4018R | IDC CABLE - MKR40K/MC40M/MCE40K |
| LTC4002ES8-4.2#PBF | IC CHARGER BATTERY LI-ION 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4006 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Standalone Li-Ion Battery Charger |
| LTC4006_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Standalone Li-Ion Battery Charger |
| LTC4006EGN-2 | 功能描述:IC CHARGER BATTERY 4A 16-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4006EGN-2#PBF | 功能描述:IC CHARGER BATTERY 4A 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4006EGN-2#TR | 功能描述:IC CHARGER BATTERY 4A 16-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。