- 您现在的位置：买卖IC网 > PDF目录15996 > LTC4006EGN-4#TR (Linear Technology)IC BATT CHGR CC/CV LI-ION 16SSOP PDF资料下载
参数资料
| 型号： | LTC4006EGN-4#TR |
| 厂商： | Linear Technology |
| 文件页数： | 14/20页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHGR CC/CV LI-ION 16SSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
LTC4006
APPLICATIO S I FOR ATIO
Table 4
highest at high input voltages. For V IN < 20V the high
MAXIMUM
AVERAGE CURRENT (A)
1
1
2
2
3
3
4
4
INPUT
VOLTAGE (V)
≤ 20
> 20
≤ 20
> 20
≤ 20
> 20
≤ 20
> 20
MINIMUM INDUCTOR
VALUE ( μ H)
40 ± 20%
56 ± 20%
20 ± 20%
30 ± 20%
15 ± 20%
20 ± 20%
10 ± 20%
15 ± 20%
current efficiency generally improves with larger MOSFETs,
while for V IN > 20V the transition losses rapidly increase
to the point that the use of a higher R DS(ON) device with
lower C RSS actually provides higher efficiency. The syn-
chronous MOSFET losses are greatest at high input volt-
age or during a short circuit when the duty cycle in this
switch is nearly 100%. The term (1 + δ? T) is generally
given for a MOSFET in the form of a normalized R DS(ON) vs
temperature curve, but δ = 0.005/ ° C can be used as an
approximation for low voltage MOSFETs. C RSS is usually
Charger Switching Power MOSFET
and Diode Selection
Two external power MOSFETs must be selected for use
with the charger: a P-channel MOSFET for the top (main)
switch and an N-channel MOSFET for the bottom (syn-
chronous) switch.
The peak-to-peak gate drive levels are set internally. This
voltage is typically 6V. Consequently, logic-level threshold
MOSFETs must be used. Pay close attention to the BV DSS
specification for the MOSFETs as well; many of the logic
level MOSFETs are limited to 30V or less.
Selection criteria for the power MOSFETs include the “ON”
resistance R DS(ON) , total gate capacitance Q G , reverse
transfer capacitance C RSS , input voltage and maximum
output current. The charger is operating in continuous
mode at moderate to high currents so the duty cycles for
the top and bottom MOSFETs are given by:
Main Switch Duty Cycle = V OUT /V IN
Synchronous Switch Duty Cycle = (V IN – V OUT )/V IN .
The MOSFET power dissipations at maximum output
current are given by:
PMAIN = V OUT /V IN (I 2MAX )(1 + δ? T)R DS(ON)
+ k(V 2IN )(I MAX )(C RSS )(f OSC )
PSYNC = (V IN – V OUT )/V IN (I 2MAX )(1 + δ? T)R DS(ON)
Where δ is the temperature dependency of R DS(ON) and k
is a constant inversely related to the gate drive current.
Both MOSFETs have I 2 R losses while the PMAIN equation
specified in the MOSFET characteristics; if not, then C RSS
can be calculated using C RSS = Q GD / ? V DS . The constant
k = 2 can be used to estimate the contributions of the two
terms in the main switch dissipation equation.
If the charger is to operate in low dropout mode or with a
high duty cycle greater than 85%, then the topside
P-channel efficiency generally improves with a larger
MOSFET. Using asymmetrical MOSFETs may achieve cost
savings or efficiency gains.
The Schottky diode D1, shown in the Typical Application
on the back page, conducts during the dead-time between
the conduction of the two power MOSFETs. This prevents
the body diode of the bottom MOSFET from turning on and
storing charge during the dead-time, which could cost as
much as 1% in efficiency. A 1A Schottky is generally a
good size for 4A regulators due to the relatively small
average current. Larger diodes can result in additional
transition losses due to their larger junction capacitance.
The diode may be omitted if the efficiency loss can be
tolerated.
Calculating IC Power Dissipation
The power dissipation of the LTC4006 is dependent upon
the gate charge of the top and bottom MOSFETs (Q G1 and
Q G2 respectively). The gate charge is determined from the
manufacturer’s data sheet and is dependent upon both the
gate voltage swing and the drain voltage swing of the
MOSFET. Use 6V for the gate voltage swing and V DCIN for
the drain voltage swing.
P D = V DCIN ? (f OSC (Q G1 + Q G2 ) + I DCIN )
includes an additional term for transition losses, which are
4006fa
14
相关PDF资料 |
PDF描述 |
|---|---|
| M3RRK-3006J | IDC CABLE - MPR30K/MC34G/MPR30K |
| LTC4006EGN-6#TR | IC BATT CHGR CC/CV LI-ION 16SSOP |
| 16YXG3900MEFC18X20 | CAP ALUM 3900UF 16V 20% RADIAL |
| M3UMK-4006R | IDC CABLE - MKS40K/MC40M/MCG40K |
| FWN2.00BK25 | FLEXO WRAP 2" BLACK 25' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4006EGN-6 | 功能描述:IC CHARGER BATTERY 4A 16-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4006EGN-6#PBF | 功能描述:IC CHARGER BATTERY 4A 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4006EGN-6#TR | 功能描述:IC BATT CHGR CC/CV LI-ION 16SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4006EGN-6#TRPBF | 功能描述:IC CHARGER BATTERY 4A 16-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4007 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Standalone Li Battery Charger |
发布紧急采购，3分钟左右您将得到回复。