- 您现在的位置：买卖IC网 > PDF目录16302 > LTC4006EGN-6#PBF (Linear Technology)IC CHARGER BATTERY 4A 16-SSOP PDF资料下载
参数资料
| 型号： | LTC4006EGN-6#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/20页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY 4A 16-SSOP |
| 标准包装： | 100 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
LTC4006
OPERATIO
t OFF =
Overview
The LTC4006 is a synchronous current mode PWM step-
down (buck) switcher battery charger controller. The charge
current is programmed by the sense resistor (R SENSE )
between the CSP and BAT pins. The final float voltage is
internally programmed to 8.4V (LTC4006-6), 12.6V
(LTC4006-2) or 16.8V (LTC4006-4) with better than ± 0.8%
accuracy. Charging begins when the potential at the DCIN
pin rises above the voltage at CLN (and the UVLO voltage)
and the ACP/SHDN pin is allowed to go high; the CHG pin
is set low. At the beginning of the charge cycle, if the cell
voltage is below 2.5V, the charger will trickle charge the
battery with 10% of the maximum programmed current.
If the cell voltage stays below 2.5V for 25% of the total
charge time, the charge sequence will be terminated im-
mediately and the CHG pin will be set to a high impedance.
An external thermistor network is sampled at regular
intervals. If the thermistor value exceeds design limits,
charging is suspended. If the thermistor value returns to
an acceptable value, charging resumes. An external resis-
tor on the R T pin sets the total charge time. The timer can
be defeated by forcing the CHG pin to a low voltage.
As the battery approaches the final float voltage, the charge
current will begin to decrease. When the current drops to
10% of the programmed charge current, an internal C/10
comparator will indicate this condition by sinking 25 μ A at the
CHG pin. The charge timer is also reset to 25% of the total
charge time. If this condition is caused by an input current
limit condition, described below, then the C/10 comparator
will be inhibited. When a time-out occurs, charging is termi-
nated immediately and the CHG pin changes to a high
impedance. The charger will automatically restart if the cell
voltage is less than 3.9V. To restart the charge cycle manu-
ally, simply remove the input voltage and reapply it, or force
the ACP/SHDN pin low momentarily. When the input voltage
is not present, the charger goes into a sleep mode, dropping
battery current drain to 15 μ A. This greatly reduces the current
drain on the battery and increases the standby time. The
ACP/SHDN pin. It controls the gate of the input FET to keep
a low forward voltage drop when charging and also
prevents reverse current flow through the input FET.
If the input voltage is less than V CLN , it must go at least
170mV higher than V CLN to activate the charger. When this
occurs the ACP/SHDN pin is released and pulled up with
an internal load to indicate that the adapter is present. The
gate of the input FET is driven to a voltage sufficient to keep
a low forward voltage drop from drain to source. If the
voltage between DCIN and CLN drops to less than 25mV,
the input FET is turned off slowly. If the voltage between
DCIN and CLN is ever less than – 25mV, then the input FET
is turned off in less than 10 μ s to prevent significant
reverse current from flowing in the input FET. In this
condition, the ACP/SHDN pin is driven low and the charger
is disabled.
Battery Charger Controller
The LTC4006 charger controller uses a constant off-time,
current mode step-down architecture. During normal opera-
tion, the top MOSFET is turned on each cycle when the
oscillator sets the SR latch and turned off when the main
current comparator I CMP resets the SR latch. While the top
MOSFET is off, the bottom MOSFET is turned on until either
the inductor current trips the current comparator I REV or the
beginning of the next cycle. The oscillator uses the equation:
V DCIN – V BAT
V DCIN ? f OSC
to set the bottom MOSFET on time. This activity is dia-
grammed in Figure 1.
The peak inductor current, at which I CMP resets the SR latch,
is controlled by the voltage on I TH . I TH is in turn controlled by
several loops, depending upon the situation at hand. The
average current control loop converts the voltage between
CSP and BAT to a representative current. Error amp CA2
OFF
TGATE
charger can be inhibited at any time by forcing the ACP/SHDN
pin to a low voltage.
Input FET
BGATE
ON
ON
OFF
t OFF
TRIP POINT SET BY ITH VOLTAGE
The input FET circuit performs two functions. It enables
the charger if the input voltage is higher than the CLN pin
and provides the logic indicator of AC present on the
INDUCTOR
CURRENT
Figure 1
4006 F01
4006fa
8
相关PDF资料 |
PDF描述 |
|---|---|
| M2MXH-6018R | IDC CABLE - MDM60H/MC60M/X |
| M3UYK-1606J | IDC CABLE - MKS16K/MC16G/MPD16K |
| LTC4006EGN-2#PBF | IC CHARGER BATTERY 4A 16-SSOP |
| M3URK-1606J | IDC CABLE - MKS16K/MC16G/MPR16K |
| VE-2WY-EX-S | CONVERTER MOD DC/DC 3.3V 49.5W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4007 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Standalone Li Battery Charger |
| LTC4007_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Standalone Li-Ion Battery Charger |
| LTC4007-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Li-Ion Battery Charger |
| LTC4007EGN | 功能描述:IC BATT CHARGER CTRLR 4A 24SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4007EGN#PBF | 功能描述:IC BATT CHARGER CTRLR 4A 24SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。