- 您现在的位置：买卖IC网 > PDF目录16302 > LTC4007EGN#PBF (Linear Technology)IC BATT CHARGER CTRLR 4A 24SSOP PDF资料下载
参数资料
| 型号： | LTC4007EGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER CTRLR 4A 24SSOP |
| 标准包装： | 55 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
LTC4007
TEST CIRCUIT
LTC4007
16
CHEM
V REF
+
7
3C4C
DIVIDER/
MUX
–
EA
14
CSP
15
BAT
10
ITH
+
LT1055
OPERATION
–
4007 TC
0.6V
Overview
The LTC4007 is a synchronous current mode PWM step-
down (buck) switcher battery charger controller. The charge
current is programmed by the combination of a program
resistor (R PROG ) from the PROG pin to ground and a sense
resistor (R SENSE ) between the CSP and BAT pins. The ?nal
?oat voltage is programmed to one of four values (12.3V,
12.6V, 16.4V, 16.8V) with ±1% maximum accuracy using
pins 3C4C and CHEM. Charging begins when the potential
at the DCIN pin rises above the voltage at BAT (and the
UVLO voltage) and the SHDN pin is low; the CHG pin is
set low. At the beginning of the charge cycle, if the cell
voltage is below 2.5V (2.44V if CHEM is low), the LOBAT
pin will be low. The LOBAT indicator can be used to reduce
the charging current to a low value, typically 10% of full
scale. If the cell voltage stays below 2.5V for 25% of the
total charge time, the charge sequence will be terminated
immediately and the FAULT pin will be set low.
An external thermistor network is sampled at regular inter-
vals. If the thermistor value exceeds design limits, charging
is suspended and the FAULT pin is set low. If the thermistor
value returns to an acceptable value, charging resumes
and the FAULT pin is set high. An external resistor on the
R T pin sets the charge termination time. Charge termination
can be defeated by forcing the CHG pin to a low voltage.
As the battery approaches the ?nal ?oat voltage, the charge
current will begin to decrease. When the current drops
to 10% of the full-scale charge current, an internal C/10
comparator will indicate this condition by latching the
FLAG pin low. The charge timer is also reset to 1/4 of the
total charge time when FLAG goes low. If this condition
is caused by an input current limit condition, described
below, then the FLAG indicator will be inhibited. When
a time-out occurs, charging is terminated immediately
and the CHG pin is forced to a high impedance state.
The charger will automatically restart if the cell voltage
is below 3.9V (or 3.81V if CHEM is low). To restart the
charge cycle manually, simply remove the input voltage
and reapply it, or set the SHDN pin high momentarily.
When the input voltage is not present, the charger goes
into a sleep mode, dropping battery current drain to 15μA.
This greatly reduces the current drain on the battery and
increases the standby time. The charger is inhibited any
time the SHDN pin is high.
Input FET
The input FET circuit performs two functions. It enables
the charger if the input voltage is higher than the CLN
pin and provides the logic indicator of AC present on the
ACP pin. It controls the gate of the input FET to keep a low
forward voltage drop when charging and also prevents
reverse current ?ow through the input FET.
If the input voltage is less than V CLN , it must go at least
170mV higher than V CLN to activate the charger. When
this occurs the ACP pin is released and pulled up with an
external load to indicate that the adapter is present. The
gate of the input FET is driven to a voltage suf?cient to
4007fc
9
相关PDF资料 |
PDF描述 |
|---|---|
| LT1513-2CR#PBF | IC BATT CHRGR CONST/PROG I/V 7DD |
| LT1513-2CR | IC BATT CHRGR CONST/PROG I/V 7DD |
| LTC4008EGN-1#PBF | IC BATT CHARGER CTRLR 4A 20SSOP |
| M3BYK-1606R | IDC CABLE - MSR16K/MC16M/MPD16K |
| M1YXK-2436J | IDC CABLE - MPD24K/MC24G/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4007EUFD-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Li-Ion Battery Charger |
| LTC4007EUFD-1#PBF | 功能描述:IC CHARGER BATTERY 4A 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4007EUFD-1#TRPBF | 功能描述:IC CHARGER BATTERY 4A 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4008 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4A, High Efficiency, Standalone Li Battery Charger |
| LTC4008EGN | 功能描述:IC BATT CHARGER CTRLR 4A 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。