- 您现在的位置：买卖IC网 > PDF目录15995 > LTC4009IUF-1#PBF (Linear Technology)IC CHARGER BATTERY MC 20-QFN PDF资料下载
参数资料
| 型号： | LTC4009IUF-1#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 23/28页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY MC 20-QFN |
| 标准包装： | 91 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN 裸露焊盘（4x4） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页
LTC4009
LTC4009-1/LTC4009-2
APPLICATIONS INFORMATION
The LTC4009 uses an improved adaptive TGATE and
BGATE drive that is insensitive to MOSFET inertial delays,
t d(ON/OFF), to avoid overlap conduction losses. Switching
characteristics from power MOSFET data sheets apply
only to a specific test fixture, so there is no substitute for
bench evaluation of external FETs in the target application.
In general, MOSFETs with lower inertial delays will yield
higher efficiency.
Diode Selection
A Schottky diode in parallel with the bottom FET and/or
top FET in an LTC4009 application clamps SW during the
non-overlap times between conduction of the top and
bottom FET switches. This prevents the body diode of the
MOSFETs from forward biasing and storing charge, which
could reduce efficiency as much as 1%. One or both diodes
can be omitted if the efficiency loss can be tolerated. A 1A
Schottky is generally a good size for 3A chargers due to the
low duty cycle of the non-overlap times. Larger diodes can
actually result in additional efficiency (transition) losses
due to larger junction capacitance.
Loop Compensation and Soft-Start
The three separate PWM control loops of the LTC4009
can be compensated by a single set of components at-
tached between the ITH pin and GND. As shown in the
typical LTC4009 application, a 6.04k resistor in series
with a capacitor of at least 0.1μF provides adequate loop
compensation for the majority of applications.
The LTC4009 can be soft-started with the compensation
capacitor on the ITH pin. At start-up, ITH will quickly rise
to about 0.25V, then ramp up at a rate set by the com-
pensation capacitor and the 40μA ITH bias current. The
full programmed charge current will be reached when ITH
reaches approximately 2V. With a 0.1μF capacitor, the time
to reach full charge current is usually greater than 1.5ms.
This capacitor can be increased if longer start-up times
are required, but loop bandwidth and dynamic response
will be reduced.
INTV DD Regulator Output
Bypass the INTV DD regulator output to GND with a low
ESR X5R or X7R ceramic capacitor with a value of 0.47μF
or larger. The capacitor used to build the BOOST supply
(C2 in Figure 11) can serve as this bypass. Do not draw
more than 30mA from this regulator for the host system,
governed by IC power dissipation.
Calculating IC Power Dissipation
The user should ensure that the maximum rated junction
temperature is not exceeded under all operating conditions.
The thermal resistance of the LTC4009 package ( θ JA ) is
37°C/W, provided the Exposed Pad is in good thermal
contact with the PCB. The actual thermal resistance in
the application will depend on forced air cooling and other
heat sinking means, especially the amount of copper on
the PCB to which the LTC4009 is attached. The following
formula may be used to estimate the maximum average
power dissipation P D (in watts) of the LTC4009, which is
dependent upon the gate charge of the external MOSFETs.
This gate charge, which is a function of both gate and drain
voltage swings, is determined from specifications or graphs
in the manufacturer’s data sheet. For the equation below,
find the gate charge for each transistor assuming 5V gate
swing and a drain voltage swing equal to the maximum
V CLP voltage. Maximum LTC4009 power dissipation under
normal operating conditions is then given by:
P D = DCIN(2.8mA + I DD + 665kHz(Q TGATE + Q BGATE ))
– 5I DD
where:
I DD = Average external INTV DD load current, if any
Q TGATE = Gate charge of external top FET in Coulombs
Q BGATE = Gate charge of external bottom FET in
Coulombs
4009fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4009IUF-2#PBF | IC CHARGER BATTERY MC 20-QFN |
| M3RRK-3420K | IDC CABLE - MPR34K/MC34F/MPR34K |
| 450QXW39MEFC10X40 | CAP ALUM 39UF 450V 20% RADIAL |
| LT1571EGN-5#TRPBF | IC CHARGER BATT CONST V/I 16SSOP |
| 415-0009-030 | CABLE SMB-RA/SMB-RA 30" RG-179 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4009IUF-2#PBF | 功能描述:IC CHARGER BATTERY MC 20-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4009IUF-2#TRPBF | 功能描述:IC CTLR BATT CHARGER CC/CV 20QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4010 | 制造商:LINEAR 制造商全称:LINEAR 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4010CFE | 制造商:Linear Technology 功能描述:Battery Charger NiCD/NiMH 16-Pin TSSOP EP |
| LTC4010CFE#PBF | 功能描述:IC CHARGER NIMH/NICD 16-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
发布紧急采购，3分钟左右您将得到回复。