- 您现在的位置：买卖IC网 > PDF目录240288 > LTC4010EFE#PBF (LINEAR TECHNOLOGY CORP) 0.2 A BATTERY CHARGE CONTROLLER, 640 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | LTC4010EFE#PBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.2 A BATTERY CHARGE CONTROLLER, 640 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | 4.40 MM, LEAD FREE, PLASTIC, TSSOP-16 |
| 文件页数： | 6/24页 |
| 文件大小： | 281K |
| 代理商： | LTC4010EFE#PBF |
LTC4010
4010fb
External DC Source
The external DC power source should be connected to the
charging system and the VCC pin through a power diode
acting as an input rectifier. This prevents catastrophic
system damage in the event of an input short to ground
or reverse-voltage polarity at the DC input. The LTC4010
automatically senses when this input drives the VCC pin
above BAT. The open-circuit voltage of the DC source
should be between 5.5V and 34V, depending on the num-
ber of cells being charged. In order to avoid low dropout
operation, ensure 100% capacity at charge termination,
and allow reliable detection of battery insertion, removal
or overvoltage, the following equation can be used to
determine the minimum full-load voltage that should be
produced at VCC when the external DC power source is
connected.
VCC(MIN) = (n 2V) + 0.3V
where n is the number of series cells in the battery pack.
The LTC4010 will properly charge over a wide range of VCC
and BAT voltage combinations. Operating the LTC4010 in
low dropout or with VCC much greater than BAT will force
the PWM frequency to be much less than 550kHz. The
LTC4010 disables charging and sets a fault if a large VCC to
BAT differential would cause generation of audible noise.
Load Control
Proper load current control is an important consideration
when fast charging nickel cells. This control ensures that
the system load remains powered at all times, but that
normal system operation and associated load transients
do not adversely affect fast charge termination. The input
protecton detailed in the previous paragraph is an integral
part of the necessary load control.
The battery should also be connected to the raw system
supply by some rectifying means, thus forming a switch
that selects the battery for system power only if an external
DC source is not present.
Battery Chemistry Selection
The desired battery chemistry is selected by program-
ming the CHEM pin to the proper voltage. If it is wired
to GND, a set of parameters specific to charging NiMH
applicaTions inForMaTion
cells is selected. When CHEM is left floating, charging is
optimized for NiCd cells. The various charging parameters
are detailed in Table 2.
Programming Charge Current
Charge current is programmed using the following
equation:
R
mV
I
SENSE
PROG
=
100
RSENSE is an external resistor connected between the
SENSEandBATpins.A1%resistorwithalowtemperature
coefficient and sufficient power dissipation capability to
avoid self-heating effects is recommended. Charge rate
should be between approximately C/2 and 2C.
Inductor Value Selection
Formanyapplications,10Hrepresentsanoptimumvalue
for the inductor the PWM uses to generate charge current.
For applications with IPROG of 1.5A or greater running
from an external DC source of 15V or less, values between
5H and 7.5H can often be selected. For wider operating
conditions the following equation can be used as a guide
for selecting the minimum inductor value.
L > 6.5 10–6 VDCIN RSENSE, L ≥ 4.7H
Actualpartselectionshouldaccountforbothmanufacturing
tolerance and temperature coefficient to ensure this mini-
mum. A good initial selection can be made by multiplying
the calculated minimum by 1.4 and rounding up or down
to the nearest standard inductance value.
Ultimately, there is no substitute for bench evaluation of
the selected inductor in the target application, which can
also be affected by other environmental factors such as
ambient operating temperature. Using inductor values
lower than recommended by the equation shown above
can result in a fault condition at the start of precharge or
top-off charge.
Programming Maximum Charge Times
Connecting the appropriate resistor between the TIMER
pin and GND programs the maximum duration of various
相关PDF资料 |
PDF描述 |
|---|---|
| LT1460GIZ-10#TRPBF1460 | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 10 V, PBCY3 |
| LZS-500-1 | 1-OUTPUT 500 W AC-DC REG PWR SUPPLY MODULE |
| LMX2330USLEX | PLL FREQUENCY SYNTHESIZER, 2500 MHz, PQCC24 |
| LM4040EEM3-2.0/NOPB | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.048 V, PDSO3 |
| LM4040BIZ-4.1/NOPB | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 4.096 V, PBCY3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4011 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
| LTC4011CFE | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4011CFE#PBF | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4011CFE#TR | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。