- 您现在的位置：买卖IC网 > PDF目录15978 > LTC4011CFE (Linear Technology)IC BATT CHARGER HIEFF 20TSSOP PDF资料下载
参数资料
| 型号： | LTC4011CFE |
| 厂商： | Linear Technology |
| 文件页数： | 12/26页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER HIEFF 20TSSOP |
| 标准包装： | 74 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 34 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 20-TSSOP-EP |
| 包装： | 管件 |
LTC4011
OPERATION
(Refer to Figure 1)
Shutdown State
The LTC4011 remains in micropower shutdown until DCIN
(Pin 1) is driven above V CC (Pin 18). In shutdown all status
and PWM outputs and internally generated terminations
or supply voltages are inactive. Current consumption from
V CC and BAT is reduced to a very low level.
Charge Qualification State
Once DCIN is greater than V CC , the LTC4011 exits
micropower shutdown, enables its own internal supplies,
provides V RT voltage for temperature sensing, and switches
V CDIV to GND to allow measurement of the average single-
cell voltage. The IC also verifies that V CC is at or above 4.2V,
V CC is 510mV above BAT and V CELL is between 350mV and
1.95V. If V CELL is below 350mV, no charging will occur, and
if V CELL is above 1.95V, the fault state is entered, which
is described in more detail below. Once adequate voltage
conditions exist for charging, READY is asserted.
If the voltage between V TEMP and GND is below 200mV, the
LTC4011 is paused. If V TEMP is above 200mV but below
2.85V, the LTC4011 verifies that the sensed temperature is
between 5°C and 45°C. If these temperature limits are not
met or if its own die temperature is too high, the LTC4011
will indicate a fault and not allow charging to begin. If V TEMP
is greater than 2.85V, battery temperature related charge
qualification, monitoring and termination are disabled.
Once charging is fully qualified, precharge begins (unless
the LTC4011 is paused). In that case, the V TEMP pin is
monitored for further control. The charge status indicators
and PWM outputs remain inactive until charging begins.
Charge Monitoring
The LTC4011 continues to monitor important voltage and
temperature parameters during all charging states. If the
DC input is removed, charging stops and the shutdown
state is entered. If V CC drops below 4.25V or V CELL drops
below 350mV, charging stops and the LTC4011 returns
to the charge qualification state. If V CELL exceeds 1.95V,
charging stops and the IC enters the fault state. If an external
thermistor indicates sensed temperature is beyond a range
of 5°C to 60°C, or the internal die temperature exceeds an
internal thermal limit, charging is suspended, the charge
timer is paused and the LTC4011 indicates a fault condition.
Normal charging resumes from the previous state when
the sensed temperature returns to a satisfactory range. In
addition, other battery faults are detected during specific
charging states as described below.
Precharge State
If the initial voltage on V CELL is below 900mV, the LTC4011
enters the precharge state and enables the PWM current
source to trickle charge using one-fifth the programmed
charge current. The CHRG status output is active during
precharge. The precharge state duration is limited to
t MAX /12 minutes, where t MAX is the maximum fast charge
period programmed with the TIMER pin. If sufficient V CELL
voltage cannot be developed in this length of time, the fault
state is entered, otherwise fast charge begins.
Fast Charge State
If adequate average single-cell voltage exists, the LTC4011
enters the fast charge state and begins charging at the
programmed current set by the external current sense
resistor connected between the SENSE and BAT pins.
The CHRG status output is active during fast charge. If
V CELL is initially above 1.325V, voltage-based termination
processing begins immediately. Otherwise –?V termination
is disabled for a stabilization period of t MAX /12. In that
case, the LTC4011 makes another fault check at t MAX /12,
requiring the average cell voltage to be above 1.22V. This
ensures the battery pack is accepting a fast charge. If
V CELL is not above this voltage threshold, the fault state is
entered. Fast charge state duration is limited to t MAX and
the fault state is entered if this limit is exceeded.
Charge Termination
Fast charge termination parameters are dependent upon
the battery chemistry selected with the CHEM pin. Voltage-
based termination (– ?V) is always active after the initial
voltage stabilization period. If an external thermistor network
is present, chemistry-specific limits for ?T/?t (rate of tem-
perature rise) are also used in the termination algorithm.
Temperature-based termination, if enabled, becomes active
as soon as the fast charge state is entered. Successful
charge termination requires a charge rate between C/2 and
2C. Lower rates may not produce the battery voltage and
temperature profile required for charge termination.
4011fb
相关PDF资料 |
PDF描述 |
|---|---|
| 100ZLJ390M12.5X40 | CAP ALUM 390UF 100V 20% RADIAL |
| EBM31DTBS | CONN EDGECARD 62POS R/A .156 SLD |
| 35ZLJ1500MGC16X20 | CAP ALUM 1500UF 35V 20% RADIAL |
| UCL0J101MCL6GS | CAP ALUM 100UF 6.3V 20% SMD |
| ESM10DTAS | CONN EDGECARD 20POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4011CFE#PBF | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4011CFE#TR | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4011CFE#TRPBF | 功能描述:IC BATT CHARGER HIEFF 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4011CFEPBF | 制造商:Linear Technology 功能描述:Standalone Nickel Battery Charg. TSSOP20 |
| LTC4011CFETR | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Efficiency Standalone Nickel Battery Charger |
发布紧急采购，3分钟左右您将得到回复。