- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4053EDD-4.2#TRPBF (Linear Technology)IC CHARGER BATTERY USB 10-DFN PDF资料下载
参数资料
| 型号： | LTC4053EDD-4.2#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY USB 10-DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
LTC4053-4.2
APPLICATIO S I FOR ATIO
Undervoltage Lockout (UVLO)
An internal undervoltage lockout circuit monitors the input
voltage and keeps the charger in shutdown mode until V CC
rises above the undervoltage lockout threshold. The UVLO
circuit has a built-in hysteresis of 150mV. Furthermore, to
protect against reverse current in the power MOSFET, the
UVLO circuit keeps the charger in shutdown mode if V CC
falls to within 35mV of the battery voltage. If the UVLO
comparator is tripped, the charger will not come out of
shutdown until V CC rises 70mV above the battery voltage.
Trickle Charge And Defective Battery Detection
At the beginning of a charge cycle, if the battery voltage is
low (below 2.48V) the charger goes into trickle charge
reducing the charge current to 10% of the full-scale
current. If the low battery voltage persists for one quarter
of the total charge time, the battery is assumed to be
defective, the charge cycle is terminated, the CHRG pin
output assumes a high impedance state, and the FAULT
pin pulls low. The fault can be cleared by toggling V CC ,
temporarily forcing the SHDN pin to 0V, or temporarily
forcing the BAT pin voltage above 2.48V.
Shutdown
The LTC4053 can be shut down (I CC = 25 μ A) by pulling the
SHDN pin to 0V. For normal operation, pull the SHDN pin
above the manual shutdown threshold voltage level. Do
For example, if 500mA charge current is required,
calculate:
R PROG = 1500V/0.5A = 3k ?
For best stability over temperature and time, 1% metal-
film resistors are recommended.
If the charger is in constant-temperature or constant-
voltage mode, the battery current can be monitored by
measuring the PROG pin voltage as follows:
I CHG = (V PROG / R PROG ) ? 1000
USB and Wall Adapter Power
Although the LTC4053 allows charging from a USB port,
a wall adapter can also be used to charge Li-Ion batteries.
Figure 2 shows an example of how to combine wall adapter
and USB power inputs. A P-channel MOSFET, MP1, is
used to prevent back conducting into the USB port when
a wall adapter is present and Schottky diode, D1, is used
to prevent USB power loss through the 1k pull-down
resistor.
Typically a wall adapter can supply significantly more
current than the 500mA-limited USB port. Therefore, an N-
channel MOSFET, MN1 and an extra 3k program resistor
can be used to increase the charge current to 1A when the
wall adapter is present.
not leave this pin open. In shutdown the internal linear
regulator is turned off, and the internal timer is reset.
Programming Charge Current
The formula for the battery charge current (see Figure 1)
5V WALL
ADAPTER
1A I CHG
USB
POWER
500mA I CHG
MP1
D1
2
V CC
LTC4053
BAT
PROG
9
7
I CHG
+
SYSTEM
LOAD
Li-Ion
is:
BATTERY
I CHG = (I PROG ) ? 1000
1k
MN1
3k
3k
= (1.5V / R PROG ) ? 1000 or
R PROG = 1500V/I CHG
where R PROG is the total resistance from the PROG pin to
4053 F02
Figure 2. Combining Wall Adapter and USB Power
ground. Under trickle charge conditions, this current is
reduced to 10% of the full-scale value.
4053fa
9
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4054ES5-4.2#TRMPBF | IC CHARGR BATTERY L-ION TSOT23-5 |
| LTC4055EUF-1#TRPBF | IC USB PWR MNGR BATT CHRGR 16QFN |
| LTC4056ETS8-4.2#TRPBF | IC CHARGR BATTERY L-ION TSOT23-8 |
| LTC4057ES5-4.2#TRPBF | IC CHARGR BATTERY L-ION TSOT23-5 |
| LTC4058XEDD-4.2#TRPBF | IC BATT CHARGER LI-ION REG 8DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4053EMSE-4.2 | 功能描述:IC CHARGER BATTERY USB 10-MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4053EMSE-4.2#PBF | 功能描述:IC CHARGER BATTERY USB 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4053EMSE-4.2#TR | 功能描述:IC BATT CHARGR LI-ION REG 10MSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4053EMSE-4.2#TRPBF | 功能描述:IC CHARGER BATTERY USB 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4054 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT |
发布紧急采购，3分钟左右您将得到回复。