- 您现在的位置：买卖IC网 > PDF目录16039 > LTC4054ES5-4.2#TR (Linear Technology)IC CHARGR BATTERY L-ION TSOT23-5 PDF资料下载
参数资料
| 型号： | LTC4054ES5-4.2#TR |
| 厂商： | Linear Technology |
| 文件页数： | 13/16页 |
| 文件大小： | 0K |
| 描述： | IC CHARGR BATTERY L-ION TSOT23-5 |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 带卷 (TR) |
LTC4054-4.2/LTC4054X-4.2
APPLICATIO S I FOR ATIO
CHRG Status Output Pin
The CHRG pin can provide an indication that the input
voltage is greater than the undervoltage lockout threshold
level. A weak pull-down current of approximately 20 μ A
indicates that sufficient voltage is applied to V CC to begin
charging. When a discharged battery is connected to the
charger, the constant current portion of the charge cycle
begins and the CHRG pin pulls to ground. The CHRG pin
can sink up to 10mA to drive an LED that indicates that a
charge cycle is in progress.
When the battery is nearing full charge, the charger enters
the constant-voltage portion of the charge cycle and the
charge current begins to drop. When the charge current
drops below 1/10 of the programmed current, the charge
cycle ends and the strong pull-down is replaced by the
20 μ A pull-down, indicating that the charge cycle has
ended. If the input voltage is removed or drops below the
undervoltage lockout threshold, the CHRG pin becomes
high impedance. Figure 5 shows that by using two
different value pull-up resistors, a microprocessor can
detect all three states from this pin.
To detect when the LTC4054 is in charge mode, force the
digital output pin (OUT) high and measure the voltage at
the CHRG pin. The N-channel MOSFET will pull the pin
voltage low even with the 2k pull-up resistor. Once the
charge cycle terminates, the N-channel MOSFET is turned
off and a 20 μ A current source is connected to the CHRG
pin. The IN pin will then be pulled high by the 2k pull-up
resistor. To determine if there is a weak pull-down current,
the OUT pin should be forced to a high impedance state.
The weak current source will pull the IN pin low through
the 800k resistor; if CHRG is high impedance, the IN pin
will be pulled high, indicating that the part is in a UVLO
state.
Reverse Polarity Input Voltage Protection
In some applications, protection from reverse polarity
voltage on V CC is desired. If the supply voltage is high
enough, a series blocking diode can be used. In other
cases, where the voltage drop must be kept low a P-
channel MOSFET can be used (as shown in Figure 6).
V +
V DD
DRAIN-BULK
DIODE OF FET
V CC
LTC4054
CHRG
800k
2k
μ PROCESSOR
OUT
V IN
LTC4054
V CC
4054 F06
IN
405442 F05
Figure 5. Using a Microprocessor to Determine CHRG State
Figure 6. Low Loss Input Reverse Polarity Protection
405442xf
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
13
相关PDF资料 |
PDF描述 |
|---|---|
| IMC1210ER330K | INDUCTOR WW 33UH 10% 1210 |
| LTC4059EDC#TRM | IC BATT CHARGER LI-ION REG 6DFN |
| GMA10DTAT | CONN EDGECARD 20POS R/A .125 SLD |
| ECM24DSXI | CONN EDGECARD 48POS DIP .156 SLD |
| EEM36DSEF | CONN EDGECARD 72POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4054L | 制造商:LINER 制造商全称:Linear Technology 功能描述:150mA Standalone Linear Li-Ion Battery Charger in ThinSOT |
| LTC4054L-4.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:150mA Standalone Linear Li-Ion Battery Charger in ThinSOT |
| LTC4054LES5-4.2 | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 10mA to 150mA 4.2V 5-Pin TSOT-23 |
| LTC4054LES5-4.2#PBF | 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:CHARGER BATTERY LI-ION 0.8A 5SOT23 制造商:Linear Technology 功能描述:CHARGER, BATTERY, LI-ION, 0.8A, 5SOT23 |
| LTC4054LES5-4.2#TR | 功能描述:IC CHARGR BATTERY L-ION TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。