- 您现在的位置：买卖IC网 > PDF目录16038 > LTC4054XES5-4.2#TRM (Linear Technology)IC CHARGR BATTERY L-ION TSOT23-5 PDF资料下载
参数资料
| 型号： | LTC4054XES5-4.2#TRM |
| 厂商： | Linear Technology |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC CHARGR BATTERY L-ION TSOT23-5 |
| 标准包装： | 500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC4054XES5-4.2 LTC4054XES5-4.2-ND |
LTC4054-4.2/LTC4054X-4.2
OPERATIO
The LTC4054 is a single cell lithium-ion battery charger
using a constant-current/constant-voltage algorithm. It
can deliver up to 800mA of charge current (using a good
I BAT =
V PROG
R PROG
?1000
thermal PCB layout) with a final float voltage accuracy of
± 1%. The LTC4054 includes an internal P-channel power
MOSFET and thermal regulation circuitry. No blocking
diode or external current sense resistor is required; thus,
the basic charger circuit requires only two external com-
ponents. Furthermore, the LTC4054 is capable of operat-
ing from a USB power source.
Normal Charge Cycle
A charge cycle begins when the voltage at the V CC pin rises
above the UVLO threshold level and a 1% program resistor
is connected from the PROG pin to ground or when a
battery is connected to the charger output. If the BAT pin
is less than 2.9V, the charger enters trickle charge mode.
In this mode, the LTC4054 supplies approximately 1/10
the programmed charge current to bring the battery volt-
age up to a safe level for full current charging. (Note: The
LTC4054X does not include this trickle charge feature).
When the BAT pin voltage rises above 2.9V, the charger
enters constant-current mode, where the programmed
charge current is supplied to the battery. When the BAT
pin approaches the final float voltage (4.2V), the LTC4054
enters constant-voltage mode and the charge current
begins to decrease. When the charge current drops to
1/10 of the programmed value, the charge cycle ends.
Programming Charge Current
The charge current is programmed using a single resistor
from the PROG pin to ground. The battery charge current
is 1000 times the current out of the PROG pin. The
program resistor and the charge current are calculated
using the following equations:
Charge Termination
A charge cycle is terminated when the charge current falls
to 1/10th the programmed value after the final float voltage
is reached. This condition is detected by using an internal,
filtered comparator to monitor the PROG pin. When the
PROG pin voltage falls below 100mV 1 for longer than
t TERM (typically 1ms), charging is terminated. The charge
current is latched off and the LTC4054 enters standby
mode, where the input supply current drops to 200 μ A.
(Note: C/10 termination is disabled in trickle charging and
thermal limiting modes).
When charging, transient loads on the BAT pin can cause
the PROG pin to fall below 100mV for short periods of time
before the DC charge current has dropped to 1/10th the
programmed value. The 1ms filter time (t TERM ) on the
termination comparator ensures that transient loads of
this nature do not result in premature charge cycle termi-
nation. Once the average charge current drops below
1/10th the programmed value, the LTC4054 terminates
the charge cycle and ceases to provide any current through
the BAT pin. In this state, all loads on the BAT pin must be
supplied by the battery.
The LTC4054 constantly monitors the BAT pin voltage in
standby mode. If this voltage drops below the 4.05V
recharge threshold (V RECHRG ), another charge cycle be-
gins and current is once again supplied to the battery. To
manually restart a charge cycle when in standby mode, the
input voltage must be removed and reapplied, or the
charger must be shut down and restarted using the PROG
pin. Figure 1 shows the state diagram of a typical charge
cycle.
R PROG =
1000 V
I CHG
, I CHG =
1000 V
R PROG
Charge Status Indicator (CHRG)
The charge status output has three different states: strong
pull-down (~10mA), weak pull-down (~20 μ A) and high
The charge current out of the BAT pin can be determined
at any time by monitoring the PROG pin voltage using the
following equation:
impedance. The strong pull-down state indicates that the
LTC4054 is in a charge cycle. Once the charge cycle has
terminated, the pin state is determined by undervoltage
Note 1: Any external sources that hold the PROG pin above 100mV will prevent the LTC4054
from terminating a charge cycle.
405442xf
8
相关PDF资料 |
PDF描述 |
|---|---|
| 415-0029-006 | CABLE SMA/SMA 6" RG-316 |
| 415-0057-060 | CABLE BNC/BNC 60" RG-59 |
| VI-254-EY-S | CONVERTER MOD DC/DC 48V 50W |
| 415-0056-060 | CABLE BNC/BNC 60" 8218 |
| XLT64PT2 | SKT TRAN ICE17C75X/18C6X8 64TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4055 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Push Button On/Off Controller |
| LTC4055EUF | 功能描述:IC USB PWR MNGR BATT CHRGR 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4055EUF#PBF | 功能描述:IC USB PWR MNGR BATT CHRGR 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4055EUF#TR | 功能描述:IC USB PWR MNGR BATT CHRGR 16QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4055EUF#TRPBF | 功能描述:IC USB PWR MNGR BATT CHRGR 16QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。