- 您现在的位置：买卖IC网 > PDF目录16040 > LTC4056ETS8-4.2#TR (Linear Technology)IC CHARGR BATTERY L-ION TSOT23-8 PDF资料下载
参数资料
| 型号： | LTC4056ETS8-4.2#TR |
| 厂商： | Linear Technology |
| 文件页数： | 7/16页 |
| 文件大小： | 0K |
| 描述： | IC CHARGR BATTERY L-ION TSOT23-8 |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.5 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 薄型，TSOT-23-8 |
| 供应商设备封装： | TSOT-23-8 |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC4056ETS8-4.2TR |
LTC4056-4.2
OPERATIO
The LTC4056 is a linear battery charger controller with a
programmable charge termination timer. Operation can
be understood by referring to the Block Diagram. A charge
cycle begins when V CC rises above the UVLO (undervoltage
lockout) threshold V UVLOI (nominally 4.4V), an external
current programming resistor is connected between the
PROG pin and ground and the TIMER/SHDN pin is allowed
to rise above the shutdown threshold V MSDT (nominally
0.82V).
If the battery voltage is below V TRIKL (2.8V) at the begin-
ning of the charge cycle, the charger goes into trickle
charge mode to bring the cell voltage up to a safe level for
charging at full current. In this mode, an internal current
source provides approximately 2% of the programmed
charge current to the BAT pin. The charger goes into the
full charge constant current mode once the voltage on the
BAT pin rises above V TRIKL + ? V TRIKL (2.9V).
During full current charging, the collector of the external
PNP provides the charge current. The PNP emitter current
flows through the I SENSE pin and through the internal
110m ? current sense resistor. This current is close in
magnitude, but slightly more than the collector current
since it includes base current. Amplifier A1 forces 1V on
the PROG pin. Therefore, a current equal to 1V/R PROG will
flow through the internal 100 ? resistor. Amplifier CA will
force the same voltage that appears across the 100 ?
resistor to appear across the internal 110m ? resistor.
This amplifier ensures that the current flowing out of the
I SENSE pin is equal to 915 times the current flowing out of
the PROG pin. Therefore, neglecting base current, the
charge current will be 915V/R PROG . This region of opera-
tion is referred to as constant current mode.
As the battery accepts charge, its voltage rises. When it
reaches the preset float voltage of 4.2V, a precisely divided
down version of this voltage (1.2V) is compared to the
1.2V internal reference voltage by amplifier VA. If the
battery voltage attempts to exceed 4.2V (1.2V at the input
of amplifier VA), the amplifier will divert current away from
the output driver thus limiting charge current to maintain
4.2V on the battery. This is the constant voltage mode.
An external capacitor on the TIMER/SHDN pin and the
resistance between the PROG pin and ground set the total
charge time. When this time elapses, the charge cycle
terminates and the CHRG pin transitions from a strong
pull-down to a weak 12 μ A pull-down. To restart the charge
cycle, simply remove the input voltage and reapply it or
momentarily force the TIMER/SHDN pin to ground. The
charge cycle will also restart if the BAT pin voltage falls
below the recharge threshold (V RECHRG is nominally 4.05V).
When V CC is applied, pulling the TIMER/SHDN pin to
ground will manually shut down the charger and reset the
timer. When this pin is released an internal 7 μ A current
source pulls the TIMER/SHDN pin above the 0.82V shut-
down threshold to resume charging.
Fault conditions such as overheating of the die or exces-
sive DRIVE pin or PROG pin current are monitored and
limited.
When input power is removed or manual shutdown is
entered, the charger will drain only tiny leakage currents
(<1 μ A) from the battery, thus maximizing battery standby
time. With V CC removed the external PNP base is con-
nected to the battery by the charger. In manual shutdown
the base is connected to V CC by the charger.
405642f
7
相关PDF资料 |
PDF描述 |
|---|---|
| IMC1210ER150K | INDUCTOR WW 15UH 10% 1210 |
| LTC4057ES5-4.2#TRMPBF | IC CHARGR BATTERY L-ION TSOT23-5 |
| IMC1210ER120K | INDUCTOR WW 12UH 10% 1210 |
| LTC4057ES5-4.2#TRM | IC CHARGR BATTERY L-ION TSOT23-5 |
| LTC4056ETS8-4.2#TRMPBF | IC CHARGR BATTERY L-ION TSOT23-8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4057 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT |
| LTC4057-4.2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Linear Li-Ion Battery Charger with Thermal Regulation in ThinSOT |
| LTC4057ES5-4.2 | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 500mA 4.2V 5-Pin TSOT-23 |
| LTC4057ES5-4.2#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 500mA 4.2V 5-Pin TSOT-23 |
| LTC4057ES5-4.2#TR | 功能描述:IC CHARGR BATTERY L-ION TSOT23-5 RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。