- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4060EDHC#TRPBF (Linear Technology)IC BATT CHARGER NIMH/NICD 16DFN PDF资料下载
参数资料
| 型号： | LTC4060EDHC#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC BATT CHARGER NIMH/NICD 16DFN |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 镍镉（NiCd）、镍金属氢化物（NiMH） |
| 电源电压： | 4.5 V ~ 10 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WFDFN 裸露焊盘 |
| 供应商设备封装： | 16-DFN（5x3） |
| 包装： | 带卷 (TR) |
LTC4060
OPERATIO
charging begins at the maximum current set by the
external programming resistor connected between the
PROG pin and GND.
If an external thermistor indicates sensed temperature is
beyond a range of 5 ° C to 55 ° C charging is suspended, the
charge timer is paused and the CHRG status output
remains low. Normal charging resumes from the previous
state when the sensed temperature rises above 5 ° C or falls
below 45 ° C. Voltage-based termination (– ? V) is then
reset and immediately enabled. If voltage-based termina-
tion was imminent when the temperature limits were
exceeded, charge termination will occur.
Charge Termination
Once fast charge begins and after an initial battery voltage
stabilization hold-off period shown in Table 1, voltage-
based termination (– ? V) is enabled. This period is used to
prevent falsely terminating on a – ? V event that can occur
almost immediately after initiating charging on some
heavily discharged or stored batteries. However, if V CELL
was measured to be above 1.3V (V IDT ) immediately prior
to the precharge cycle, then a mostly charged battery is
assumed and voltage-based termination (– ? V) is enabled
without delay.
An internal 1.5mV resolution A/D converter measures the
cell voltage after each battery voltage sampling interval
indicated in Table 1. The peak cell voltage is stored and
compared to the current cell voltage. When the cell voltage
has dropped by at least V MDV (magnitude selected by the
CHEM pin) from the peak for four consecutive battery
voltage sampling intervals, charging is terminated.
Back-up termination is provided by the charge time limiter,
whose time limit is indicated in Table 1, and by a battery
overvoltage detector. Once terminated by back-up termi-
nation, charge qualification can be reinitiated only by remov-
ing and replacing the battery or toggling the SHDN pin low
to high or removing and reapplying power to the charger.
Automatic Recharge
Once charging is complete, the optional programmable
automatic recharge state can be entered. This state, if
enabled, will automatically restart the charger from the
charge qualification state without user intervention when-
ever the battery cell voltage drops below a set level. With
the advent of low memory effect NiMH and improved NiCd
cells an automatic recharge feature is practical and elimi-
nates the need for very slow trickle charging.
The CHRG status output is high impedance in the auto-
matic recharge state until charging begins. If the V CELL
voltage drops below the voltage set on the ARCT pin for at
least the automatic recharge entry delay time as shown in
Table 1, the charge qualification state is entered and
charging will begin anew in fast charge. An easy way of
setting the voltage on the ARCT pin is by using two series
current programming resistors and connecting their com-
mon to the ARCT pin as shown in Figure 2. The PROG pin
will provide a constant 1.5V (V PROG ). The programmable
voltage range of the ARCT pin is approximately 0.8V to
1.6V. A preprogrammed recharge threshold of 1.3V (V ARDT )
is selected when the ARCT pin is connected to V CC
(V ARDEF ). Automatic recharge is disabled when the ARCT
pin is connected to ground (V ARDIS ).
Pause
After charging is initiated, the PAUSE pin may be used to
pause operation at any time. Whenever the voltage on the
PAUSE pin is a logic high, the charge timer and all other
timers pause, charging is stopped and the fast charge ter-
mination algorithm is inhibited. The CHRG status output
remains at GND. If voltage-based termination was immi-
nent before pause, charge termination will occur. Otherwise,
when pause ends, the charge timer and all other timers
resume timing, charging restarts and voltage-based termi-
nation (– ? V) is reset and immediately enabled. If the bat-
tery is removed while the PAUSE pin is a logic high, then
battery removal is detected and shutdown is entered. If the
battery is replaced while the PAUSE pin is a logic high, it
will not be detected until pause is turned off.
For pause periods or a series of periods where the battery
capacity could be significantly depleted, consider using
shutdown instead of pause to avoid having the safety timer
expire before the battery can be fully charged. Shutdown
resets the safety timer.
4060f
11
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4061EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4062EDD#TRPBF | IC BATT CHARGER LI-ION 10-DFN |
| LTC4063EDD#TRPBF | IC BATT CHRGR LI-ION LDO 10DFN |
| LTC4064EMSE#TRPBF | IC CHARGER BATT L-ION 4V 10-MSOP |
| LTC4065EDC#TRPBF | IC CHARGER BATT LI-ON 6-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4060EFE | 制造商:Linear Technology 功能描述:Battery Charger NiCD/NiMH 2000mA -0.3V to 10.3V 16-Pin TSSOP EP |
| LTC4060EFE#PBF | 功能描述:IC BATT CHARGR NIMH/NICD 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4060EFE#TRPBF | 功能描述:IC BATT CHARGR NIMH/NICD 16TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4060EFEPBF | 制造商:Linear Technology 功能描述:LTC4060 NiCd/NiMH 2A standalone charger |
| LTC4061 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone Linear Li-lon Battery Charger with Thermistor Input |
发布紧急采购，3分钟左右您将得到回复。