- 您现在的位置：买卖IC网 > PDF目录16028 > LTC4064EMSE#TR (Linear Technology)IC CHARGER BATT L-ION 4V 10-MSOP PDF资料下载
参数资料
| 型号： | LTC4064EMSE#TR |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATT L-ION 4V 10-MSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
LTC4064
APPLICATIO S I FOR ATIO
Programming The Timer
Table 1.
The programmable timer is used to terminate the charge
cycle. The timer duration is programmed by an external
capacitor at the TIMER pin. The total charge time is:
Time (Hours) = (3 Hours) ? (C TIMER /0.1 μ F) or
C TIMER = 0.1 μ F ? Time (Hours)/3 (Hours)
The timer starts when an input voltage greater than the
undervoltage lockout threshold level is applied and the
SHDN pin is greater than the manual shutdown threshold
voltage level. After a time-out occurs, the charge current
stops, and the CHRG output assumes a high impedance
state to indicate that the charging has stopped. Connect-
ing the TIMER pin to ground disables the timer function.
Recharge
After a charge cycle has terminated, if the battery voltage
drops below the recharge threshold of 3.90V a new charge
cycle will begin. The recharge circuit integrates the BAT
FAULT
High
Low
High
Low
High
Low
CHRG
Low
Low
30 μ A
pull-down
30 μ A
pull-down
High
High
Description
Charge cycle has started, C/10 has not been
reached and charging is proceeding normally.
Charge cycle has started, C/10 has not been
reached, but the charge current and timer
have been paused due to an NTC out-of-
temperature condition.
C/10 has been reached and charging is
proceeding normally.
C/10 has been reached but the charge current
and timer have paused due to an NTC out-of-
temperature condition.
Normal timeout (charging has terminated).
If FAULT goes low and CHRG goes high
impedance simultaneously, then the LTC4064
has timed out due to a bad cell (V BAT <2.48V
after one-quarter the programmed charge time).
If CHRG goes high impedance first, then
the LTC4064 has timed out normally (charging
has terminated), but NTC is indicating an out-
of-temperature condition.
pin voltage for a few milliseconds to prevent a transient
from restarting the charge cycle.
If the battery voltage remains below 2.48V during trickle
charge for 1/4 of the programmed time, the battery may be
defective and the charge cycle will end. In addition, the
recharge comparator is disabled and a new charge cycle
will not begin unless the input voltage is toggled off-then-
on, the SHDN pin is momentarily pulled to ground, or the
BAT pin is pulled above the 2.48V trickle charge threshold.
Open-Drain Status Outputs
The LTC4064 has three open-drain status outputs: ACPR,
CHRG and FAULT. The ACPR pin pulls low when an input
voltage greater than the undervoltage lockout threshold is
applied and becomes high impedance when power (V IN <
V UV ) is removed. CHRG and FAULT work together to
indicate the status of the charge cycle. Table 1 describes
the status of the charge cycle based on the CHRG and
FAULT outputs.
CHRG Status Output Pin
When the charge cycle starts, the CHRG pin is pulled to
ground by an internal N-channel MOSFET capable of
driving an LED. When the charge current drops to 10% of
the full-scale current (C/10), the N-channel MOSFET is
latched off and a weak 30 μ A current source to ground is
connected to the CHRG pin. After a time-out occurs,
the pin assumes a high impedance state. By using two
different value pull-up resistors a microprocessor can
detect three states from this pin (charging, C/10 and time-
out). See Figure 3.
When the LTC4064 is in charge mode, the CHRG pin is
pulled low by the internal N-channel MOSFET. To detect
this mode, force the digital output pin, OUT, high and
measure the voltage at the CHRG pin. The N-channel
MOSFET will pull the pin low even with the 2k pull-up
resistor. Once the charge current drops to 10% of the
sn4064 4064fs
10
相关PDF资料 |
PDF描述 |
|---|---|
| 415-0018-036 | CABLE MCX/MCX 36" RG-316 |
| VI-J04-EZ-F1 | CONVERTER MOD DC/DC 48V 25W |
| LTC4064EMSE#PBF | IC CHARGER BATT L-ION 4V 10-MSOP |
| LTC4064EMSE | IC CHARGER BATT L-ION 4V 10-MSOP |
| VI-J04-EY-S | CONVERTER MOD DC/DC 48V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4065 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone 750mA Li-Ion Battery Charger in 2 】 2 DFN |
| LTC4065A | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone 750mA Li-Ion Battery Charger in 2 】 2 DFN |
| LTC4065AEDC | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone 750mA Li-Ion Battery Charger in 2 】 2 DFN |
| LTC4065AEDC#PBF | 制造商:Linear Technology 功能描述:Constant Current/Voltage Charger Li-Ion 500mA 4.2V 6-Pin DFN EP |
| LTC4065AEDC#TR | 功能描述:IC CHARGER BATT LI-ON 6-DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。