- 您现在的位置：买卖IC网 > PDF目录1833 > LTC4068EDD-4.2#PBF (Linear Technology)IC CHARGER BATT LI-ON 8-DFN PDF资料下载
参数资料
| 型号： | LTC4068EDD-4.2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATT LI-ON 8-DFN |
| 标准包装： | 121 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
LTC4068-4.2/LTC4068X-4.2
APPLICATIO S I FOR ATIO
The LTC4068 can be used above 52 ° C ambient but the
charge current will be reduced from the programmed
800mA. The approximate current at a given ambient
temperature can be approximated by:
ceramic capacitors. Because of the self-resonant and high
Q characteristics of some types of ceramic capacitors,
high voltage transients can be generated under some
start-up conditions such as connecting the charger input
to a live power source. Adding a 1.5 ? resistor in series
( V CC BAT ) ? θ JA
I BAT =
120 ° C – T A
– V
with an X5R ceramic capacitor will minimize start-up
voltage transients. For more information, see Application
Note 88.
Using the previous example with an ambient temperature
of 60 ° C, the charge current will be reduced to
approximately:
Charge Current Soft-Start
The LTC4068 includes a soft-start circuit to minimize the
I BAT =
120 ° C – 60 ° C
( 5 V – 3 . 3 V ) ? 50 ° C / W
I BAT = 706 mA
=
60 ° C
85 ° C / A
inrush current at the start of a charge cycle. When a charge
cycle is initiated, the charge current ramps from zero to
full-scale current over a period of approximately 100 μ s.
This has the effect of minimizing the transient current load
on the power supply during start-up.
Moreover, when thermal feedback reduces the charge cur-
rent the voltage at the PROG pin is also reduced proportion-
ally as discussed in the Operation section. It is important
to remember that LTC4068 applications do not need to be
designed for worst-case thermal conditions since the IC will
automatically reduce power dissipation when the junction
temperature reaches approximately 120 ° C.
Thermal Considerations
In order to deliver maximum charge current under all
conditions, it is critical that the exposed metal pad on the
backside of the LTC4068 package is soldered to the PC
board ground. Correctly soldered to a 2500mm 2 double-
sided 1oz copper board, the LTC4068 has a thermal
resistance of approximately 40 ° C/W. Failure to make
thermal contact between the exposed pad on the back-
side of the package and the copper board will result in
USB and Wall Adapter Power
The LTC4068 allows charging from both a wall adapter
and a USB port. Figure 3 shows how to combine wall
adapter and USB power inputs. A P-channel MOSFET,
MP1, is used to prevent back conducting into the USB port
when a wall adapter is present and a Schottky diode, D1,
is used to prevent USB power loss through the 1k pull-
down resistor.
Typically a wall adapter can supply more current than
the 500mA-limited USB port. Therefore, an N-channel
MOSFET, MN1, and an extra 3.3k program resistor are
used to increase the charge current to 800mA when the
wall adapter is present. The charge termination threshold
remains fixed at 80mA.
5V WALL
thermal resistances far greater than 40 ° C/W. As an
example, a correctly soldered LTC4068 can deliver over
800mA to a battery from a 5V supply at room tempera-
ture. Without a good backside thermal connection, this
number will drop considerably.
ADAPTER
800mA I CHG
USB POWER
500mA I CHG
MP1
1k
D1
6
4, 9
LTC4068-4.2
BAT
V CC ITERM
GND PROG
3.3k
MN1
2
1
5
2k
I CHG
1.25k
+
SYSTEM
LOAD
Li-Ion
BATTERY
V CC Bypass Capacitor
Many types of capacitors can be used for input bypassing;
however, caution must be exercised when using multilayer
406842 F03
Figure 3. Combining Wall Adapter and USB Power
406842fa
10
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4069EDC#TRPBF | IC CHARGER LI-ION 6-DFN |
| LTC4070IMS8E#TRPBF | IC BATT CHRGR LIION/POLY 8MSOP |
| LTC4071IMS8E#TRPBF | IC LI-ION/POLY BATT CHRGR 8-MSOP |
| LTC4075EDD#TRPBF | IC CHARG BATT LI-ON USB 10DFN |
| LTC4076EDD#TRPBF | IC CHARG BATT LI-ON USB 10DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4068XEDD-4.2 | 功能描述:IC CHARGER BATT LI-ON 8-DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4068XEDD-4.2#PBF | 功能描述:IC CHARGER BATT LI-ON 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4068XEDD-4.2#TR | 功能描述:IC CHARGER BATT LI-ON 8-DFN RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4068XEDD-4.2#TRPBF | 功能描述:IC CHARGER BATT LI-ON 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4069 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone 750mA Li-Ion Battery Charger in 2 × 2 DFN with NTC Thermistor Input |
发布紧急采购，3分钟左右您将得到回复。