- 您现在的位置：买卖IC网 > PDF目录16310 > LTC4068XEDD-4.2#PBF (Linear Technology)IC CHARGER BATT LI-ON 8-DFN PDF资料下载
参数资料
| 型号： | LTC4068XEDD-4.2#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATT LI-ON 8-DFN |
| 标准包装： | 121 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.25 V ~ 6.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
LTC4068-4.2/LTC4068X-4.2
OPERATIO
The LTC4068 is a single cell lithium-ion battery charger
using a constant-current/constant-voltage algorithm. It
can deliver up to 950mA of charge current (using a good
thermal PCB layout) with a final float voltage accuracy of
± 1%. The LTC4068 includes an internal P-channel power
MOSFET and thermal regulation circuitry. No blocking
diode or external current sense resistor is required; thus,
Programming Charge Termination
The charge cycle terminates when the charge current
falls below the programmed termination threshold. This
threshold is set by connecting an external resistor, R TERM ,
from the ITERM pin to ground. The charge termination
current threshold (I TERM) is set by the following equation:
= CHG ? , R TERM =
the basic charger circuit requires only two external com-
ponents. Furthermore, the LTC4068 is capable of operat-
ing from a USB power source.
I TERM =
100 V
R TERM
I R PROG
10 R TERM
100 V
I TERM
Normal Charge Cycle
A charge cycle begins when the voltage at the V CC pin rises
above the UVLO threshold level and a 1% program resistor
is connected from the PROG pin to ground. If the BAT pin
is less than 2.9V, the charger enters trickle charge mode.
In this mode, the LTC4068 supplies approximately 1/10th
the programmed charge current to bring the battery volt-
age up to a safe level for full current charging. (Note: The
LTC4068X does not include this trickle charge feature.)
When the BAT pin voltage rises above 2.9V, the charger
enters constant-current mode where the programmed
charge current is supplied to the battery. When the BAT pin
approaches the final float voltage (4.2V), the LTC4068
The termination condition is detected by using an internal
filtered comparator to monitor the ITERM pin. When the
ITERM pin voltage drops below 100mV * for longer than
t TERM (typically 1ms), charging is terminated. The charge
current is latched off and the LTC4068 enters standby
mode where the input supply current drops to 200 μ A.
(Note: Termination is disabled in trickle charging and
thermal limiting modes.)
I TERM can be set to be 1/10th of I CHG by shorting the ITERM
pin to the PROG pin, thus eliminating the need for external
resistor R TERM . When configured in this way, I TERM is
always set to I CHG /10, and the programmed charge current
is set by the equation:
enters constant-voltage mode and the charge current
begins to decrease. When the charge current drops to the
programmed termination threshold (set by the external
I CHG =
500 V
R PROG
, R PROG =
500 V
I CHG
**
resistor R TERM ), the charge cycle ends.
Programming Charge Current
The charge current is programmed using a single resistor
from the PROG pin to ground. The charge current out of
the BAT pin is 1000 times the current out of the PROG pin.
The program resistor and the charge current are calcu-
lated using the following equations:
When charging, transient loads on the BAT pin can cause
the ITERM pin to fall below 100mV for short periods of
time before the DC charge current has dropped to 10% of
the programmed value. The 1ms filter time (t TERM ) on the
termination comparator ensures that transient loads of
this nature do not result in premature charge cycle termi-
nation. Once the average charge current drops below the
programmed termination threshold, the LTC4068 termi-
R PROG =
1000 V
I CHG
, I CHG =
1000 V
R PROG
nates the charge cycle and ceases to provide any current
out of the BAT pin. In this state, any load on the BAT pin
must be supplied by the battery.
Charge current out of the BAT pin can be determined at any
time by monitoring the PROG pin voltage and using the
following equation:
The LTC4068 constantly monitors the BAT pin voltage in
standby mode. If this voltage drops below the 4.1V recharge
I BAT =
V PROG
R PROG
? 1000
* Any external sources that hold the ITERM pin above 100mV will prevent the LTC4068 from
terminating a charge cycle.
** These equations apply only when the ITERM pin is shorted to the PROG pin.
406842fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4085EDE#PBF | IC USB POWER MANAGER 14-DFN |
| A3DDH-4418M | IDC CABLE - AKR44H/AE44M/AKR44H |
| 3-1906015-6 | CA 2.0MM OFNR 50/125,LC SEC GRN |
| RCM18DRYI | CONN EDGECARD 36POS DIP .156 SLD |
| RBC05DRTN-S93 | CONN EDGECARD 10POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4069 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone 750mA Li-Ion Battery Charger in 2 × 2 DFN with NTC Thermistor Input |
| LTC4069-4.4 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Standalone 750mA Li-Ion Battery Charger in 2 × 2 DFN with NTC Thermistor Input |
| LTC4069EDC#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion 500mA 4.2V 6-Pin DFN EP 制造商:Linear Technology 功能描述:BATT CHARGER LI-ION 0.75A 6 制造商:Linear Technology 功能描述:BATT CHARGER, LI-ION, 0.75A, 6DFN |
| LTC4069EDC#TRMPBF | 功能描述:IC CHARGER LI-ION 6-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4069EDC#TRPBF | 功能描述:IC CHARGER LI-ION 6-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。