- 您现在的位置：买卖IC网 > PDF目录98003 > LTC4075HVXEDD (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 PDF资料下载
参数资料
| 型号： | LTC4075HVXEDD |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| 封装： | 3 X 3 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件页数： | 2/16页 |
| 文件大小： | 170K |
| 代理商： | LTC4075HVXEDD |
LTC4075HVX
10
4075hvxf
OPERATION
Automatic Recharge
In standby mode, the charger sits idle and monitors the
battery voltage using a comparator with a 4.1ms lter time
(tRECHRG). A charge cycle automatically restarts when the
battery voltage falls below 4.075V (which corresponds to
approximately 80% to 90% battery capacity). This ensures
that the battery is kept at, or near, a fully charged condi-
tion and eliminates the need for periodic charge cycle
initiations.
If the battery is removed from the charger, a sawtooth
waveform appears at the battery output. This is caused
by the repeated cycling between termination and recharge
events. This cycling results in pulsing at the CHRG output;
an LED connected to this pin will exhibit a blinking pattern,
indicating to the user that a battery is not present. The
frequency of the sawtooth is dependent on the amount
of output capacitance.
Manual Shutdown
The ENABLE pin has a 2MΩ pull-down resistor to GND. The
denition of this pin depends on which source is supplying
power. When the wall adapter input is supplying power,
logic low enables the charger and logic high disables it
(the internal pull-down resistor defaults the charger to the
charging state). The opposite is true when the USB input is
supplying power; logic low disables the charger and logic
high enables it (the default is the shutdown state).
The DCIN input draws 40μA when the charger is in shut-
down mode. The USBIN input draws 40μA during shutdown
if no voltage is applied to DCIN, but draws only 23μA when
VDCIN provides valid voltage (see Table 1).
Status Indicators
The charge status open drain output (CHRG) has two
states: pull-down and high impedance. The pull-down
state indicates that the LTC4075HVX is in a charge cycle.
Once the charge cycle has terminated or the LTC4075HVX
is disabled, the pin state becomes high impedance.
The power supply status open drain output (PWR) has
two states: pull-down and high impedance. The pull-down
state indicates that power is present at either DCIN or
USBIN. This output is strong enough to drive an LED. If no
valid voltage is applied at either pin, the PWR pin is high
impedance, indicating that the LTC4075HVX lacks valid
input voltage (see Table 1) to charge the battery.
Table 1. Power Source Selection
VUSBIN < 3.95V or
VUSBIN < BAT + 50mV
6V > VUSBIN > 3.95V and
VUSBIN > BAT + 50mV
22V > VUSBIN > 6V
ENABLE
HIGH
LOW or No Connect
HIGH
LOW or No Connect
HIGH
LOW or No Connect
VDCIN < 4.15V or
VDCIN < BAT + 50mV
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from
USBIN source.
PWR: LOW
USBPWR: Hi-Z
CHRG: LOW
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
6V > VDCIN > 4.15V
and VDCIN > BAT +
50mV
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from DCIN
source.
PWR: LOW
USBPWR: LOW
CHRG: LOW
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from DCIN
source.
PWR: LOW
USBPWR: LOW
CHRG: LOW
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
Charging from DCIN
source.
PWR: LOW
USBPWR: LOW
CHRG: LOW
22V > VDCIN > 6V
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
No Charging.
PWR: Hi-Z
USBPWR: LOW
CHRG: Hi-Z
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4080EMSE | 0.8 A BATTERY CHARGE CONTROLLER, 2750 kHz SWITCHING FREQ-MAX, PDSO10 |
| LTC4085EDE-3#TRPBF | POWER SUPPLY MANAGEMENT CKT, PDSO14 |
| LTC4090EDJC#TRPBR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO22 |
| LTC6103CMS8#TR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| LTC6103HMS8#TR | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4075HVXEDD#PBF | 功能描述:IC CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4075HVXEDD#PBF | 制造商:Linear Technology 功能描述:BATT CHARGER LI ON DUAL 10DFN 制造商:Linear Technology 功能描述:BATT CHARGER, LI ON, DUAL, 10DFN |
| LTC4075HVXEDD#TRPBF | 功能描述:IC CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4075X | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Input USB/AC Adapter Standalone Li-Ion Battery Chargers |
| LTC4075XEDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Input USB/AC Adapter Standalone Li-Ion Battery Chargers |
发布紧急采购，3分钟左右您将得到回复。