参数资料
| 型号： | LTC4080EMSE#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/20页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER LI-ION 10-MSOP |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 3.75 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 10-MSOP 裸露焊盘 |
| 包装： | 带卷 (TR) |
LTC4080
OPERATIO
If the die temperature starts to creep up above 115°C
due to internal power dissipation, the transconductance
ampli?er, TA, limits the die temperature to approximately
115°C by reducing the charge current. Diode D3 ensures
that TA does not affect the charge current when the die
temperature is below 115°C. In thermal regulation, the
PROG pin voltage continues to give an indication of the
charge current.
In typical operation, the charge cycle begins in constant-
current mode with the current delivered to the battery equal
to 400V/R PROG . If the power dissipation of the LTC4080
results in the junction temperature approaching 115°C,
the ampli?er (TA) will begin decreasing the charge current
to limit the die temperature to approximately 115°C. As
the battery voltage rises, the LTC4080 either returns to
constant-current mode or enters constant-voltage mode
straight from constant-temperature mode.
Battery Charger Undervoltage Lockout (UVLO)
An internal undervoltage lockout circuit monitors the
input voltage and keeps the battery charger off until V CC
rises above 3.6V and approximately 80mV above the BAT
pin voltage. The 3.6V UVLO circuit has a built-in hysteresis
of approximately 0.6V, and the 80mV automatic shutdown
threshold has a built-in hysteresis of approximately 50mV.
During undervoltage lockout conditions, maximum battery
drain current is 5μA and maximum supply current is 10μA.
Undervoltage Charge Current Limiting (UVCL)
The battery charger in the LTC4080 includes undervoltage
charge current limiting that prevents full charge current
until the input supply voltage reaches approximately 300mV
above the battery voltage ( Δ V UVCL1 ). This feature is particu-
larly useful if the LTC4080 is powered from a supply with
long leads (or any relatively high output impedance). See
Applications Information section for further details.
Trickle Charge and Defective Battery Detection
At the beginning of a charge cycle, if the battery volt-
age is below 2.9V, the battery charger goes into trickle
charge mode, reducing the charge current to 10% of the
programmed current. If the low battery voltage persists
for one quarter of the total time (1.125 hr), the battery is
assumed to be defective, the charge cycle terminates and
12
the ? C ? H ? R ? G pin output pulses at a frequency of 2Hz with
a 75% duty cycle. If, for any reason, the battery voltage
rises above 2.9V, the charge cycle will be restarted. To
restart the charge cycle (i.e., when the dead battery is
replaced with a discharged battery less than 2.9V), the
charger must be reset by removing the input voltage and
reapplying it or temporarily pulling the E ? N ? _ ? C ? H ? R ? G ? pin above
the shutdown threshold.
Battery Charger Shutdown Mode
The LTC4080’s battery charger can be disabled by pulling
the ? E ? N ? _ ? C ? H ? R ? G pin above the shutdown threshold (V IH ).
In shutdown mode, the battery drain current is reduced
to less than 2μA and the V CC supply current to about 5μA
provided the regulator is off. When the input voltage is
not present, the battery charger is in shutdown and the
battery drain current is less than 5μA.
Power Supply Status Indicator ( ? A ? C ? P ? R)
The power supply status output has two states: pulldown
and high impedance. The pulldown state indicates that V CC
is above the undervoltage lockout threshold and at least
82mV above the BAT voltage (see Undervoltage Lockout).
When these conditions are not met, the ? A ? C ? P ? R pin is high
impedance indicating that the LTC4080 is unable to charge
the battery.
? C ? H ? R ? G Status Output Pin
The charge status indicator pin has three states: pulldown,
pulse at 2Hz (see Defective Battery Detection) and high
impedance. The pulldown state indicates that the battery
charger is in a charge cycle. A high impedance state indi-
cates that the charge current has dropped below 10% of
the full-scale current or the battery charger is disabled.
When the timer runs out (4.5 hrs), the ? C ? H ? R ? G pin is also
forced to the high impedance state. If the battery charger
is not in constant-voltage mode when the charge current
is forced to drop below 10% of the full-scale current by
UVCL, ? C ? H ? R ? G will stay in the strong pulldown state.
Charge Current Soft-Start
The LTC4080’s battery charger includes a soft-start circuit
to minimize the inrush current at the start of a charge cycle.
When a charge cycle is initiated, the charge current ramps
4080fb
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4081EDD#TRPBF | IC USB POWER MANAGER 10-DFN |
| LTC4085EDE#TRPBF | IC USB POWER MANAGER 14-DFN |
| LTC4088EDE#TRPBF | IC BATT CHARGER/USB 14-DFN |
| LTC4089EDJC-5#TRPBF | IC USB POWER MANAGER 22-DFN |
| LTC4090EDJC-5#TRPBF | IC USB POWER MANAGER 22-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4080X | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Standalone Li-Ion Charger with Integrated 300mA Synchronous Buck in 3mm × 3mm DFN |
| LTC4080XEDD#PBF | 功能描述:IC CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4080XEDD#TRPBF | 功能描述:IC CHARGER LI-ION 10-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC4080XEDD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Standalone Li-Ion Charger with Integrated 300mA Synchronous Buck in 3mm × 3mm DFN |
| LTC4080XEDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:500mA Standalone Li-Ion Charger with Integrated 300mA Synchronous Buck in 3mm × 3mm DFN |
发布紧急采购，3分钟左右您将得到回复。