- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4089EDJC-5#TRPBF (Linear Technology)IC USB POWER MANAGER 22-DFN PDF资料下载
参数资料
| 型号： | LTC4089EDJC-5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC USB POWER MANAGER 22-DFN |
| 标准包装： | 2,500 |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 22-WFDFN 裸露焊盘 |
| 供应商设备封装： | 22-DFN（6x3）裸露焊盘 |
| 包装： | 带卷 (TR) |
LTC4089/LTC4089-5
PIN FUNCTIONS
GND (Pins 1, 2): Ground. Tie the GND pin to a local ground
plane below the LTC4089 and the circuit components.
HVOUT (Pins 3, 18) : Voltage Output of the High Voltage
Regulator. When suf?cient voltage is present at HVOUT,
the low voltage power path from IN to OUT will be discon-
nected and the HVPR pin will be pulled low to indicate
that a high voltage wall adapter has been detected. The
LTC4089 high voltage regulator will maintain just enough
differential voltage between HVOUT and BAT to keep the
battery charger MOSFET out of dropout (typically 300mV
from OUT to BAT). The LTC4089-5 high voltage regula-
tor will provide a ?xed 5V output to the battery charger
MOSFET. HVOUT should be bypassed with at least 10μF
battery. This feature is disabled if no power is present on
HVIN, IN or BAT (i.e., below UVLO thresholds).
CHRG (Pin 8): Open-Drain Charge Status Output. When
the battery is being charged, the CHRG pin is pulled low by
an internal N-channel MOSFET. When the timer runs out or
the charge current drops below 10% of the programmed
charge current or the input supply is removed, the CHRG
pin is forced to a high impedance state.
PROG (Pin 9): Charge Current Program. Connecting a
resistor, R PROG , to ground programs the battery charge
current. The battery charge current is programmed
as follows:
to GND. Connect pins 3 and 18 with a resistance no
greater than 1 .
I CHG ( A ) =
50, 000 V
R PROG
V C (Pin 4): Leave the V C pin ?oating or bypass to ground
with a 10pF capacitor. This optional 10pF capacitor reduces
HVOUT ripple in discontinuous mode.
NTC (Pin 5): Input to the NTC Thermistor Monitoring
Circuits. Under normal operation, tie a thermistor from
the NTC pin to ground and a resistor of equal value from
NTC to VNTC. When the voltage on this pin is above 0.74
? V VNTC (Cold, 0°C) or below 0.29 ? V VNTC (Hot, 50°C)
the timer is suspended but not cleared, the charging is
disabled and the CHRG pin remains in its former state.
When the voltage on NTC comes back between 0.74 ?
V VNTC and 0.29 ? V VNTC , the timer continues where it
left off and charging is re-enabled if the battery voltage
is below the recharge threshold. There is approximately
3°C of temperature hysteresis associated with each of the
input comparators.
Connect the NTC pin to ground to disable this feature. This
will disable all of the LTC4089 NTC functions.
VNTC (Pin 6): Output Bias Voltage for NTC. A resistor from
this pin to the NTC pin will bias the NTC thermistor.
HVPR (Pin 7): High Voltage Present Output. Active low
open drain output pin. A low on this pin indicates that the
high voltage regulator has suf?cient voltage to charge the
GATE (Pin 10): External ideal diode gate pin. This pin can
be used to drive the gate of an optional external PFET con-
nected between BAT (drain) and OUT (source). By doing
so, the impedance of the ideal diode between BAT and
OUT can be reduced. When not in use, this pin should be
left ?oating. It is important to maintain a high impedance
on this pin and minimize all leakage paths.
BAT (Pin 11): Connect to a single cell Li-Ion battery. This
pin is used as an output when charging the battery and as
an input when supplying power to OUT. When the OUT pin
potential drops below the BAT pin potential, an ideal diode
function connects BAT to OUT and prevents V OUT from
dropping more than 100mV below V BAT . A precision internal
resistor divider sets the ?nal ?oat (charging) potential on
this pin. The internal resistor divider is disconnected when
IN and HVIN are in undervoltage lockout.
IN (Pin 12): Input Supply. Connect to USB supply, V BUS .
Input current to this pin is limited to either 20% or 100%
of the current programmed by the CLPROG pin as de-
termined by the state of the HPWR pin. Charge current
(to the BAT pin) supplied through the input is set to the
current programmed by the PROG pin but will be limited
by the input current limit if charge current is set greater
than the input current limit.
40895fc
8
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4090EDJC-5#TRPBF | IC USB POWER MANAGER 22-DFN |
| LTC4095EDC#TRPBF | IC CHARGER LI-ION/POLY 8-DFN |
| LTC4096XEDD#TRPBF | IC CHARGER LI-ION DL 10-DFN |
| LTC4097EDDB#TRPBF | IC CHARGER LI-ION/POLY 12-DFN |
| LTC4098EUDC#TRPBF | IC CHARGER USB COMP 20-UTQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4090 | 制造商:LINER 制造商全称:Linear Technology 功能描述:USB Power Manager with 2A High Voltage Bat-Track Buck Regulator |
| LTC4090-5 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual-Input Power Manager |
| LTC4090EDJC#PBF | 功能描述:IC USB POWER MANAGER 22-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4090EDJC#PBF | 制造商:Linear Technology 功能描述:IC POWER CONTROL/MANAGEMENT CMOS LLCC |
| LTC4090EDJC#TRPBF | 功能描述:IC USB POWER MANAGER 22-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。