- 您现在的位置：买卖IC网 > PDF目录16038 > LTC4096XEDD#PBF (Linear Technology)IC CHARGER LI-ION DL 10-DFN PDF资料下载
参数资料
| 型号： | LTC4096XEDD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER LI-ION DL 10-DFN |
| 标准包装： | 121 |
| 功能： | 充电管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.25 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 管件 |
LTC4096/LTC4096X
OPERATION
Programming Charge Termination
The charge cycle terminates when the charge current
falls below the programmed termination threshold during
constant-voltage mode. This threshold is set by connect-
ing an external resistor, R ITERM , from the ITERM pin to
ground.
The charge termination current threshold (I TERMINATE ) is
set by the following equation:
during trickle charge mode would be 80mA and 50mA,
respectively.
The LTC4096X has no trickle charge mode.
Automatic Recharge
In standby mode, the charger sits idle and monitors the
battery voltage using a comparator with a 1.6ms ?lter time
(t RECHRG ). A charge cycle automatically restarts when the
R ITERM =
100 V
I TERMINATE
, I TERMINATE =
100 V
R ITERM
battery voltage falls below 4.15V (which corresponds to
approximately 80%-90% battery capacity). This ensures
that the battery is kept at, or near, a fully charged condi-
The termination condition is detected by using an internal
?ltered comparator to monitor the ITERM pin. When the
ITERM pin voltage drops below 100mV* for longer than
t TERMINATE (typically 3ms), the charge cycle terminates,
charge current latches off and the LTC4096 enters standby
mode. When charging, transient loads on the BAT pin can
cause the ITERM pin to fall below 100mV for short periods
of time before the DC charge current has dropped below
the programmed termination current. The 3ms ?lter time
(t TERMINATE ) on the termination comparator ensures that
transient loads of this nature do not result in premature
charge cycle termination. Once the average charge current
drops below the programmed termination threshold, the
LTC4096 terminates the charge cycle and stops providing
any current out of the BAT pin. In this state, any load on
the BAT pin must be supplied by the battery.
Low-Battery Charge Conditioning (Trickle Charge)
This feature ensures that deeply discharged batteries are
gradually charged before applying full charge current. If
the BAT pin voltage is below 2.9V, the LTC4096 supplies
1/10th of the full charge current to the battery until the
BAT pin rises above 2.9V. For example, if the charger is
programmed to charge at 800mA from the wall adapter
input and 500mA from the USB input, the charge current
tion and eliminates the need for periodic charge cycle
initiations. If the battery is removed from the charger, a
sawtooth waveform appears at the battery output. This
is caused by the repeated cycling between termination
and recharge events. This cycling results in pulsing at the
? C ? H ? R ? G output; an LED connected to this pin will exhibit
a blinking pattern, indicating to the user that a battery is
not present. The frequency of the sawtooth is dependent
on the amount of output capacitance.
Status Indicators
The charge status output ( C ? H ? R ? G ? ) has two states: pull-down
and high impedance. The pull-down state indicates that
the LTC4096 is in a charge cycle. Once the charge cycle
has terminated or the LTC4096 is disabled, the pin state
becomes high impedance. The pull-down state is capable
of sinking up to 10mA.
The power present output (PWR) has two states: DCIN/
USBIN voltages and high impedance. These states are
described in Table 1 and the circuit is shown in Figure
2. The high impedance state indicates that voltage is
not present at either DCIN or USBIN, so LTC4096 lacks
suf?cient power to charge the battery. The PWR present
output is capable of sourcing up to 120mA steady state
and includes short circuit protection.
*Any external sources that hold the ITERM pin above 100mV will prevent the LTC4096 from
terminating a charge cycle.
4096xf
10
相关PDF资料 |
PDF描述 |
|---|---|
| MAX6323DUT29+T | IC SUPERVISOR 2.93V SOT23-6 |
| LTC4096EDD#PBF | IC CHARGER LI-ION DL 10-DFN |
| LTC2942CDCB#TRPBF | IC FUEL/GAS GAUGE LI-ION 6DFN |
| MAX6753KA46+T | IC MPU/RESET CIRC SOT23-8 |
| 415-0029-018 | CABLE SMA/SMA 18" RG-316 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4097 | 制造商:LINER 制造商全称:Linear Technology 功能描述:USB/Wall Adapter Standalone Li-Ion/Polymer Battery Charger |
| LTC4097EDDB | 制造商:LINER 制造商全称:Linear Technology 功能描述:USB/Wall Adapter Standalone Li-Ion/Polymer Battery Charger |
| LTC4097EDDB#PBF | 制造商:Linear Technology 功能描述:Battery Charger Li-Ion/Li-Pol 1200mA 4.2V 12-Pin DFN EP |
| LTC4097EDDB#TRMPBF | 功能描述:IC CHARGER LI-ION/POLY 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:2,000 系列:Impedance Track™ 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.4 V ~ 2.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:20-TSSOP 包装:带卷 (TR) 产品目录页面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名称:296-21665-2 |
| LTC4097EDDB#TRPBF | 功能描述:IC CHARGER LI-ION/POLY 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。