- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4098EUDC#TRPBF (Linear Technology)IC CHARGER USB COMP 20-UTQFN PDF资料下载
参数资料
| 型号： | LTC4098EUDC#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 22/32页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER USB COMP 20-UTQFN |
| 标准包装： | 2,500 |
| 系列： | Bat-Track™, PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN-EP（3x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4098/LTC4098-1
APPLICATIONS INFORMATION
( )
R CLPROG =
h CLPROG + 1
CLPROG Resistor and Capacitor
As described in the Bat-Track Input Current Limited Step
Down Switching Regulator section, the resistor on the
CLPROG pin determines the average input current limit
in each of the six current limit modes. The input cur-
rent will be comprised of two components, the current
that is used to drive V OUT and the quiescent current of
the switching regulator. To ensure that the total average
input current remains below the USB specification, both
components of input current should be considered. The
Electrical Characteristics table gives the typical values for
quiescent currents in all settings as well as current limit
programming accuracy. To get as close to the 500mA or
100mA specifications as possible, a precision resistor
should be used.
Higher or lower input currents may be programmed with
the use of a resistor other than the recommended 3.01k.
The resistor value can be calculated using the formula:
V CLPROG
I NOM ? I VBUSQ
where I NOM is the desired nominal input current limit. Note
that this resistor will affect all input current limit settings
and may cause the LTC4098/LTC4098-1 to exceed USB
current specifications.
An averaging capacitor is required in parallel with the
resistor so that the switching regulator can determine
the average input current. This capacitor also provides
the dominant pole for the feedback loop when current
limit is reached. To ensure stability, the capacitor on
CLPROG should be 0.1μF or larger.
Choosing the Inductor
Because the input voltage range and output voltage range
of the PowerPath switching regulator are both fairly nar-
row, the LTC4098/LTC4098-1 were designed for a specific
inductance value of 3.3μH. Some inductors which may be
suitable for this application are listed in Table 3.
V BUS and V OUT Bypass Capacitors
The style and value of capacitors used with the LTC4098/
LTC4098-1 determine several important parameters such
as regulator control loop stability and input voltage
ripple. Because the LTC4098/LTC4098-1 use a step-down
switching power supply from V BUS to V OUT , its input
current waveform contains high frequency components.
It is strongly recommended that a low equivalent series
resistance (ESR) multilayer ceramic capacitor be used
to bypass V BUS . Tantalum and aluminum capacitors are
not recommended because of their high ESR. The value
of the capacitor on V BUS directly controls the amount
of input ripple for a given load current. Increasing the
size of this capacitor will reduce the input ripple. The
USB specification allows a maximum of 10μF to be con-
nected directly across the USB power bus. If additional
capacitance is required for noise performance, it may be
connected directly to the V BUS pin when using the OVP
feature of the LTC4098/LTC4098-1. This extra capacitance
will be soft-connected over several milliseconds to limit
inrush current and avoid excessive transient voltage
drops on the bus.
To prevent large V OUT voltage steps during transient
load conditions, it is also recommended that a ceramic
capacitor be used to bypass V OUT . The output capacitor
Table 3. Recommended Inductors for the LTC4098/LTC4098-1
INDUCTOR TYPE
L
(μH)
MAX I DC MAX DCR
(A) ( Ω )
SIZE IN mm
(L × W × H)
MANUFACTURER
LPS4018
D53LC
DB318C
WE-TPC Type M1
CDRH6D12
CDRH6D38
3.3
3.3
3.3
3.3
3.3
3.3
2.2
2.26
1.55
1.95
2.2
3.5
0.08
0.034
0.070
0.065
0.0625
0.020
3.9 × 3.9 × 1.7
5 × 5 × 3
3.8 × 3.8 × 1.8
4.8 × 4.8 × 1.8
6.7 × 6.7 × 1.5
7 × 7 × 4
Coilcraft
www.coilcraft.com
Toko
www.toko.com
Würth Elektronik
www.we-online.com
Sumida
www.sumida.com
40981fc
22
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4099EUDC#PBF | IC USB PWR MANAGER/CHRGR 20-QFN |
| LTC4100EG#TR | IC CHARGER SMART BATTERY 24-SSOP |
| LTC4101EG#PBF | IC CNTRLR BATT CHRG 24-SSOP |
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4099 | 制造商:LINER 制造商全称:Linear Technology 功能描述:I2C Controlled USB Power Manager/Charger with Overvoltage Protection |
| LTC4099EPDC#PBF | 功能描述:IC USB PWR MANAGER/CHRGR 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC4099EPDC#TRMPBF | 制造商:Linear Technology 功能描述: |
| LTC4099EPDC#TRPBF | 功能描述:IC USB PWR MANAGER/CHRGR 20UTQFN RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:PowerPath™ 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC4099EPDC-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:I2C Controlled USB Power Manager/Charger with Overvoltage Protection |
发布紧急采购，3分钟左右您将得到回复。