- 您现在的位置：买卖IC网 > PDF目录16300 > LTC4100EG#PBF (Linear Technology)IC SMART BATTERY CHARGER 24-SSOP PDF资料下载
参数资料
| 型号： | LTC4100EG#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/30页 |
| 文件大小： | 0K |
| 描述： | IC SMART BATTERY CHARGER 24-SSOP |
| 标准包装： | 59 |
| 功能： | 充电管理 |
| 电池化学： | 智能电池 |
| 电源电压： | 6 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC4100
OPERATION
The RES_COLD bit is set only when the SafetySignal
resistance value is greater than 28.5kΩ. The SafetySignal
indicates a cold battery. The RES_COLD bit will be set
whenever the RES_OR bit is set.
The RES_HOT bit is set only when the SafetySignal
resistance is less than 3150Ω, which indicates a hot battery.
The RES_HOT bit will be set whenever the RES_UR bit is set.
The RES_UR bit is set only when the SafetySignal resis-
tance value is less than 575Ω.
ALARM_INHIBITED bit is set if a valid AlarmWarning()
message has been received and charging is inhibited as
a result. This bit is cleared if both ChargingVoltage() and
ChargingCurrent() are rewritten to the LTC4100, power
is removed (DCDIV < V ACP ), or if a battery is removed.
The setting of the ALARM_INHIBITED will activate the
LTC4100 SMBALERT pull-down.
POWER_FAIL bit is set if the LTC4100 does not have suf-
ficient DCIN voltage to charge the battery or if an external
device is pulling the CHGEN input signal low. Charging
is disabled whenever this bit is set. The setting of this bit
does not clear the values in the ChargingVoltage() and
ChargingCurrent() function values, nor does it necessarily
affect the charging modes of the LTC4100.
BATTERY_PRESENT is set if a battery is present other-
wise it is cleared. The LTC4100 uses the SafetySignal
in order to determine battery presence. If the LTC4100
detects a RES_OR condition, the BATTERY_PRESENT
bit is cleared immediately. The LTC4100 will not set the
BATTERY_PRESENT bit until it successfully samples
the SafetySignal twice and does not detect a RES_OR
condition on either sampling. If AC is not present (e.g.
DCDIV < V ACP ), this bit may not be set for up to one-half
second after the battery is connected to the SafetySignal.
The ChargingCurrent() and ChargingVoltage() function
values are immediately cleared whenever this bit is cleared.
Charging will never be allowed if this bit is cleared. A
change in BATTERY_PRESENT will activate the LTC4100
SMBALERT pull-down.
AC_PRESENT is set if the voltage on DCDIV is greater than
V ACP . This does not necessarily indicate that the voltage
on DCIN is sufficient to charge the battery. A change
in AC_PRESENT will activate the LTC4100 SMBALERT
pull-down.
ChargingCurrent() (‘h14)
Description: The Battery, System Host or other master
device sends the desired charging current (mA) to the
LTC4100 .
Purpose: The LTC4100 uses R ILIM , the granularity of the
I DAC , and the value of the ChargingCurrent() function to
determine its charging current supplied to the battery. The
charging current will never exceed the maximum current
permitted by R ILIM . The ChargingCurrent() value will be
truncated to the granularity of the I DAC . The charging cur-
rent will also be reduced if the battery voltage exceeds the
programmed charging voltage.
? SMBus Protocol: Write Word.
Input: The CHARGING_CURRENT is an unsigned 16 bit
integer specifying the requested charging current in mA.
The following table defines the maximum permissible
value of CHARGING_CURRENT that will not set the
CURRENT_OR in the ChargerStatus() function for a given
value of the R ILIM :
R ILIM ChargingCurrent() Current
Short to GND 0x0000 through 0x03FF 0mA through 1023mA
10kΩ ±1% 0x0000 through 0x07FF 0mA through 2047mA
33kΩ ±1% 0x0000 through 0x0BFF 0mA through 3071mA
Open (or Short to V DD ) 0x0000 through 0x0FFF 0mA through 4095mA
ChargingVoltage() (‘h15)
Description: The Battery, SMBus Host or other master
device sends the desired charging voltage (mV) to the
LTC4100.
Purpose: The LTC4100 uses R VLIM , the granularity of the
V DAC , and the value of the ChargingVoltage() function to
determine its charging voltage supplied to the battery. The
charging voltage will never be forced beyond the voltage
permitted by R VLIM . The ChargingVoltage() value will be
truncated to the granularity of the V DAC . The charging
voltage will also be reduced if the battery current exceeds
the programmed charging current.
? SMBus Protocol: Write Word.
Input: The CHARGING_VOLTAGE is an unsigned 16-bit
integer specifying the requested charging voltage in mV.
14
For more information www.linear.com/LTC4100
4100fc
相关PDF资料 |
PDF描述 |
|---|---|
| ESC18DREH-S13 | CONN EDGECARD 36POS .100 EXTEND |
| LT1513IR#PBF | IC BATT CHRGR CONST/PROG I/V 7DD |
| 4-1906052-0 | CA 2MM OFNR 62.5/125,LC SEC BLU |
| ABC06DRTS-S13 | CONN EDGECARD 12POS .100 EXTEND |
| MAX4090EVKIT+ | KIT EVALUATION FOR MAX4090 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4100EGTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Smart Battery Charger Controller |
| LTC4101 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Smart Battery Charger Controller |
| LTC4101EG | 制造商:LINER 制造商全称:Linear Technology 功能描述:Smart Battery Charger Controller |
| LTC4101EG#PBF | 功能描述:IC CNTRLR BATT CHRG 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4101EG#TRPBF | 功能描述:IC CNTRLR BATT CHRG 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。