- 您现在的位置：买卖IC网 > PDF目录20683 > LTC4151CDD-1#TRPBF (Linear Technology)IC CURRENT MONITOR(12BIT) 10DFN PDF资料下载
参数资料
| 型号： | LTC4151CDD-1#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 10/18页 |
| 文件大小： | 435K |
| 描述： | IC CURRENT MONITOR(12BIT) 10DFN |
| 标准包装： | 2,500 |
| 功能： | 电流监控器（12 位） |
| 检测方法： | 高端 |
| 精确度： | ±1% |
| 输入电压： | 7 V ~ 80 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-DFN（3x3） |
| 包装： | 带卷 (TR) |
LTC4151
10
4151ff
For more information www.linear.com/LTC4151
Using Opto-Isolators with LTC4151-1 and LTC4151-2
The LTC4151-1/LTC4151-2 split the SDA line into SDAI
(input) and SDAO (LTC4151-1 inverted output) or SDAO
(LTC4151-2 output) for convenience of opto-coupling
with a host controller that sits at a different ground level.
When using opto-isolators with the LTC4151-1, connect
the SDAI to the output of the incoming opto-coupler and
connect the SDAO to the anode of the outgoing opto-
coupler (see Figure 9). With the outgoing opto-coupler
clamping SDAO and internal 6V (5.5V minimum) clamps
on SDAI and SCL, the pull-up resistors on these three pins
can be directly connected to V
IN
. In this way (with SDAO
rather than conventional SDAO), the need for a separate
low voltage supply for pull-ups is eliminated.
Figure 11 shows the LTC4151-2 with high speed opto-
couplers for faster bus speeds. The LTC4151-2 has a non-
inverter SDAO output. Powered from V
IN
, the high voltage
LT3010-5 low dropout regulator provides the supply for the
opto-couplers as well as the bus lines pull-up. If the SDAI
and SDAO on the master controller are not tied together,
the ACK bit of the SDAO must be returned back to SDAI.
Start and Stop Conditions
When the I
2
C bus is idle, both SCL and SDA must remain
in the high state. A bus master signals the beginning of a
transmission with a Start condition by transitioning SDA
from high to low while SCL stays high. When the master
has finished communicating with the slave, it issues a Stop
condition by transitioning SDA from low to high while SCL
stays high. The bus is then free for another transmission.
Stuck-Bus Reset
The LTC4151 I
2
C interface features a stuck-bus reset
timer. The low conditions of the SCL and the SDA/SDAI
pins are ORed to start the timer. The timer is reset when
both SCL and SDA/SDAI are pulled high. If the SCL pin or
the SDA/SDAI pin is held low for over 33ms, the stuck-bus
timer will expire and the internal I
2
C state machine will be
reset to allow normal communication after the stuck-bus
condition is cleared. The stuck-bus timer can be disabled
by clearing control register bit G2.
applicaTions inForMaTion
Figure 9. Opto-Isolation of the I
2
C Interface Between LTC4151-1 and a
Microcontroller (1.5kHz Data Rate of I
2
C is Limited by Slew Rate of Opto-Isolators)
4151 F09
3.3V
R
S
0.02
?CONTROLLER
GND
LTC4151-1
SCL
SCL
V
IN
48V
V
IN
V
DD
V
ADIN
SDAI
ADIN
ADR1
R5
0.51k
R6
10k
R7
10k
R4
0.51k
R1
20k
R2
20k
R3
5.1k
1
8
2
7
3
6
4
5
8
1
7
2
6
3
5
4
SDA
ADR0
GND
SENSE
+
SENSE
SDA0
MOCD207M
MOCD207M
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4151CDD#TRPBF | IC CURRENT MONITOR(12BIT) 10DFN |
| A7SSB-0910M | CABLE D-SUB-AFM09B/AE09M/AFM09B |
| GSM08DRKH-S13 | CONN EDGECARD 16POS .156 EXTEND |
| MIC2810-44MYML TR | IC REG TRPL BUCK/LINEAR 16-MLF |
| RMM43DSEI | CONN EDGECARD 86POS .156 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4151CDD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage I2C Current and Voltage Monitor |
| LTC4151CDD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage I2C Current and Voltage Monitor |
| LTC4151CMS#PBF | 功能描述:IC CURRENT MONITOR(12BIT) 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳流/电流管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 功能:电流开关 检测方法:- 精确度:±10% 输入电压:1.7 V ~ 5.5 V 电流 - 输出:600mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-UFQFN 供应商设备封装:10-UTQFN（1.4x1.8） 包装:管件 |
| LTC4151CMS#PBF | 制造商:Linear Technology 功能描述:MONITOR, CURRENT & VOLTAGE, I2C, MSOP-10 |
| LTC4151CMS#TRPBF | 功能描述:IC CURRENT MONITOR(12BIT) 10MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳流/电流管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 功能:电流开关 检测方法:- 精确度:±10% 输入电压:1.7 V ~ 5.5 V 电流 - 输出:600mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-UFQFN 供应商设备封装:10-UTQFN（1.4x1.8） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。