- 您现在的位置：买卖IC网 > PDF目录16303 > LTC4160EUDC#PBF (Linear Technology)IC SWITCH POWER MANAGER 20-QFN PDF资料下载
参数资料
| 型号： | LTC4160EUDC#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 25/32页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH POWER MANAGER 20-QFN |
| 标准包装： | 91 |
| 系列： | Bat-Track™, PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页
LTC4160/LTC4160-1
APPLICATIONS INFORMATION
R NTC
100k
–
+
NTCBIAS
R NOM
105k
NTC
R1
12.7k
T
3
4
LTC4160/LTC4160-1
NTC BLOCK
0.765 ? NTCBIAS
+
–
0.349 ? NTCBIAS
+
0.1V –
TOO_COLD
TOO_HOT
NTC_ENABLE
switching and V BUS will be held at the regulation voltage
of the external supply. If the external supply has a lower
regulation voltage and is capable of only sourcing current,
then V BUS will be regulated to 5.1V. The external supply
will not source current to V BUS .
For a supply that can also sink current and has a regulation
voltage less than 5.1V, the bidirectional switching regulator
will source current into the external supply in an attempt
to bring V BUS up to 5.1V. As long as the external supply
holds V BUS to more than V OUT + 70mV, the bidirectional
switching regulator will source up to 680mA into the sup-
ply. If V BUS is held to a voltage that is less than V OUT +
70mV then the short circuit timer will shut off the switching
regulator after 7.2ms. The FAULT pin will then go low to
indicate a short circuit current fault.
41601 F08
Figure 8. Modified NTC Configuration
Hot Plugging and USB Inrush Current Limiting
The overvoltage protection circuit provides inrush current
limiting due to the long time it takes for OVGATE to fully
enhance the N-channel MOSFET. This prevents the current
from building up in the cable too quickly and dampens
out any resonant overshoot on V BUS . It is possible to
observe voltage overshoot on V BUS when connecting the
LTC4160/LTC4160-1 to a lab supply if the overvoltage
protection circuit is not used. This overshoot is caused by
the inductance of the long leads from the supply to V BUS .
Twisting the wires together from the supply to V BUS can
greatly reduce the parasitic inductance of these long leads
and keep V BUS at a safe level. USB cables are generally
manufactured with the power leads in close proximity and
thus have fairly low parasitic inductance.
Hot Plugging and USB On-The-Go
If there is more than 4.3V on V BUS when On-The-Go is
enabled, the bidirectional switching regulator will not try
to drive V BUS . If USB On-The-Go is enabled and an external
supply is then connected to V BUS , one of three things will
happen depending on the properties of the external sup-
ply. If the external supply has a regulation voltage higher
than 5.1V, the bidirectional switching regulator will stop
V BUS Bypass Capacitance and USB On-The-Go
Session Request Protocol
When two On-The-Go devices are connected, one will be
the A device and the other will be the B device depending
on whether the device is connected to a micro-A or micro-
B plug. The A device provides power to the B device and
starts as the host. To prolong battery life, the A device
can power down V BUS when the BUS is not being used.
If the A device has powered down V BUS , the B device can
request the A device to power up V BUS and start a new
session using the session request protocol (SRP). The
SRP consists of data-line pulsing and V BUS pulsing. The
B device must first pulse the D + or D – data lines. The B
device must then pulse V BUS only if the A device does not
respond to the data-line pulse. The A device is required
to respond to only one of the pulsing methods. USB A
devices that never power down V BUS are not required to
respond to the SRP.
For V BUS pulsing, the limit on the V BUS capacitance on
the A device allows a B device to differentiate between a
powered down On-The-Go device and a powered down
standard host. The B device will send out a pulse of current
that will raise V BUS to a voltage between 2.1 and 5.25V if
connected to an On-The-Go A device which must have no
more than 6.5μF. An On-The-Go A device must drive V BUS
as soon as the current pulse raises V BUS above 2.1V if the
device is capable of responding to V BUS pulsing.
41601fa
25
相关PDF资料 |
PDF描述 |
|---|---|
| LT1579CS-5#PBF | IC LDO REG SMART DUAL 5V 16-SOIC |
| 3-6754413-1 | CA,XG,MTRJ-SC |
| LT1579CS-5 | IC LDO REG SMART DUAL 5V 16-SOIC |
| 3-6754412-1 | CA,XG,MTRJ-SC |
| LT1510CS8#PBF | IC BATT CHARGER CONST V/I 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4210 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4210-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Hot Swap Controller in 6-Lead SOT-23 Package |
| LTC42101CS6 | 制造商:Linear Technology 功能描述: |
| LTC4210-1CS6 | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 |
| LTC4210-1CS6#PBF | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 6-Pin TSOT-23 制造商:Linear Technology 功能描述:IC HOT SWAP CONT 制造商:Linear Technology 功能描述:HOT SWAP CNTRL 16.5VIN 6SOT23 制造商:Linear Technology 功能描述:HOT SWAP, CNTRL, 16.5VIN, 6SOT23 制造商:Linear Technology 功能描述:IC, HOT SWAP CONT; Controller Applications:Hot Board Insertion, Electronic Circuit Breaker, Industrial High Side Switch; Input Voltage:16.5V; Internal Switch:Yes; Supply Voltage Min:2.7V; Supply Voltage Max:16.5V; No. of Pins:6 ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。