- 您现在的位置：买卖IC网 > PDF目录19857 > LTC4211IMS#TR (Linear Technology)IC CONTROLLER HOT SWAP 10-MSOP PDF资料下载
参数资料
| 型号： | LTC4211IMS#TR |
| 厂商： | Linear Technology |
| 文件页数： | 11/40页 |
| 文件大小： | 321K |
| 描述： | IC CONTROLLER HOT SWAP 10-MSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 2.5 V ~ 16.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC4211IMSTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
LTC4211
11
4211fb
PIN FUNCTIONS (8-Lead Package/10-Lead Package)
clamps at the GATE pin determine the gate drive voltage
(擵
GATE
= V
GATE
V
CC
). The charge pump produces a
minimum 4.5V of 擵
GATE
for supplies in the range of 2.7V
d V
CC
< 4.75V. For 4.75V d V
CC
d 12V the 擵
GATE
is limited
by zener clamp Z1 connected between the GATE and V
CC
pins. The 擵
GATE
is typically at 12V and with guaranteed
minimum value of 10V. For V
CC
> 12V, the Zener clamp
Z2 begins to set the limitation for 擵
GATE
. Z2 clamps the
gate voltage to ground to 26V typically. The minimum Z2s
clamp voltage is 23V. This effectively sets 擵
GATE
to 8V
minimum at V
CC
= 15V.
SENSE (Pin 7/Pin 8): Circuit Breaker Set Pin. With a sense
resistor placed in the power path between V
CC
and SENSE,
the LTC4211s electronic circuit breaker trips if the voltage
across the sense resistor exceeds the thresholds set inter-
nally for the SLOW COMP and the FAST COMP, as shown
in the Block Diagram. The threshold for the SLOW COMP is
V
CB(SLOW)
= 50mV, and the electronic circuit breaker trips
if the voltage across the sense resistor exceeds 50mV for
20約. The SLOW COMP delay is fixed in the S8/MS8 ver-
sion and adjustable in the MS version of the LTC4211. To
adjust the SLOW COMPs delay, please refer to the section
on Adjusting SLOW COMPs Response Time.
Under transient conditions where large step current
changes can and do occur over shorter periods of time,
a second (fast) comparator instead trips the electronic
circuit breaker. The threshold for the FAST COMP is set at
V
CB(FAST)
= 150mV, and the circuit breaker trips if the
voltage across the sense resistor exceeds 150mV for
more than 300ns. The FAST COMPs delay is fixed in the
LTC4211 and cannot be adjusted. To disable the electronic
circuit breaker, connect the V
CC
and SENSE pins together.
V
CC
(Pin 8/Pin 9): This is the positive supply input to
the LTC4211. The LTC4211 operates from 2.5V < V
CC
<
16.5V, and the supply current is typically 1mA. An internal
undervoltage lockout circuit disables the device until the
voltage at V
CC
exceeds 2.3V.
FAULT (Not available on S8/MS8, Pin 10 MS): FAULT is
both an input and an output. Connected to this pin are an
analog comparator (COMP6) and an open-drain N-channel
FET. During normal operation, if COMP6 is driven below
1.236V, the electronic circuit breaker trips and the GATE
pin pulls low. Typically, a 10k pull-up resistor connects
to the FAULT pin. This pull-up is required to allow the
LTC4211 to begin a second timing cycle (V
FAULT
> 1.286)
and start-up properly. This also allows the use of the
FAULT pin as a status output. Under normal operating
conditions, the FAULT output is a logic high. Two condi-
tions cause an active low on FAULT: (1) the LTC4211s
electronic circuit breaker trips because of an output short
circuit causing a fast output overcurrent transient (FAST
COMP trips circuit breaker); or (2) V
FILTER
> 1.236V. The
FAULT output is driven to logic low and is latched logic
low until the ON pin is driven to logic low for 150約 (the
t
RESET
duration).
FILTER (Not available S8/MS8, Pin 3 MS): Overcurrent
Fault Timing Pin and Overvoltage Fault Set pin. With a
capacitor connected from this pin to ground, the SLOW
COMPs response time can be adjusted. In the S8/MS8
version of the LTC4211, the FILTER pin is not available
and the delay time from overcurrent detect to GATE OFF
is fixed at 20約.
相关PDF资料 |
PDF描述 |
|---|---|
| AMM25DRTF-S13 | CONN EDGECARD 50POS DIP .156 SLD |
| M4A5-192/96-12VNI | IC CPLD 192MACRO 144TQFP |
| GBB60DHBD | CONN EDGECARD 120PS R/A .050 SLD |
| MAX8888EZK25+T | IC REG LDO 2.5V .3A TSOT23-5 |
| TIM104K035P0X | CAP TANT 0.1UF 35V 10% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4211IS8 | 功能描述:IC CTRLR HOTSWAP CURR CTRL 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4211IS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4211IS8#TR | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4211IS8#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4212 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。