- 您现在的位置：买卖IC网 > PDF目录19909 > LTC4216IMS#TRPBF (Linear Technology)IC CNTRLR HOT SWAP 10-MSOP PDF资料下载
参数资料
| 型号： | LTC4216IMS#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 19/26页 |
| 文件大小： | 311K |
| 描述： | IC CNTRLR HOT SWAP 10-MSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 2.3 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
LTC4216
19
4216fa
For more information www.linear.com/LTC4216
applicaTions inForMaTion
1. Maximum drain-to-source voltage, V
DS(MAX)
The V
DS(MAX)
rating must exceed the maximum load sup-
ply voltage including spikes and ringing.
2. Gate-to-source voltage, V
GS
, overdrive
The absolute maximum rating for V
GS
is typically ?V for
logic level and sub-logic level MOSFETs.
3. Drain-to-source resistance, R
DS(ON)
The R
DS(ON)
should be low for low voltage applications
to allow its drain-to-source voltage, V
DS(ON)
, to be a very
small percentage of the supply voltage.
To begin a design, first specify the maximum operating load
current and load capacitance. Calculate the R
SENSE
value
from Equation (12). The minimum trip current, I
TRIP(MIN)
,
given by Equation (14) should be set to accommodate the
maximum operating load current.
During the start-up cycle, the LTC4216 may operate the
MOSFET in analog current limit, forcing 擵
ACL(TH)
between
32mV to 48mV across R
SENSE
. The minimum inrush current
given by Equation (16) is calculated using the minimum
擵
ACL(TH)
and maximum R
SENSE
value.
I
V
R
mV
R
INRUSH MIN
ACL THMIN
SENSE MAX
SENSE MAX
( )
( , )
( )
=
=
32
(16)
The maximum short-circuit current given by Equation (17)
is calculated using the maximum 擵
ACL(TH)
and minimum
R
SENSE
value.
I
V
R
mV
R
SHORT CIRCUIT MAX
ACL THMAX
SENSE MIN
SENSE MIN
=
=
( )
( , )
( )
48
(17)
Select the FILTER capacitor, C3, based on the slowest
expected charging rate; otherwise, FILTER might time-out
before the load capacitor is fully charged. A value for C3
is calculated based on the maximum time it takes the load
capacitor, C
LOAD
, to charge to its maximum value of load
supply (V
IN(MAX)
). That time is given by:
t
C
V
I
CHARGE LOAD
LOAD IN MAX
INRUSH MIN
(
)
( )
"
=
(18)
Rearranging Equation (2) for the circuit breaker response
time, the FILTER capacitor, C3, is given by:
C
t
s
A
V
CHARGE LOAD
3
20
60
1 2
=
?/DIV>
?/DIV>
(
)"
.
(
)
(19)
Returning to Equation (2), the circuit breaker response
time is calculated with a chosen C3 and used in conjunc-
tion with V
IN(MAX)
and I
SHORT-CIRCUIT(MAX)
to check the
SOA curves of a prospective MOSFET.
As a numerical design example for the Typical Application,
consider V
IN(MAX)
= 1.8V + 5%, maximum operating load
current = 5A, C
LOAD
= 1000礔. Equation (12) gives R
SENSE
= 4.3m? Choose R
SENSE
= 4m??1% tolerance. From
Equations (14) and (16), I
TRIP(MIN)
= 5.3A (> I
LOAD(MAX)
= 5A) and I
INRUSH(MIN)
= 7.9A respectively. Equation (19)
gives C3 = 10nF. To account for errors in C3, FILTER current
(60礎) and FILTER threshold (1.253V), the calculated value
should be multiplied by 1.5, giving the nearest standard
value of C3 = 18nF.
If a short-circuit occurs, a current of up to I
SHORT-
CIRCUIT(MAX)
= 12.1A will flow through the MOSFET for
400祍 as dictated by C3 = 18nF in Equation (2). The
MOSFET must be selected based on this criterion and
checked against the SOA curve.
V
CC
Supply RC Network
The LTC4216 has two separate pins, V
CC
and SENSEP,
for supply input and sensing:
1. V
CC
pin for powering the internal circuitry.
2. SENSEP pin, together with the SENSEN pin, for sens-
ing the current flowing from the load supply through the
external sense resistor and N-channel MOSFET to the
output load.
In most Hot Swap devices, V
CC
and SENSEP are one
common pin, providing the devices supply and external
MOSFETs current sensing. However, supply dips due
to output short can potentially trigger the device into an
undervoltage lockout condition, causing the device to
disable and its internal latches to reset.
As bypass capacitors are not allowed on the powered
supply side of the external MOSFET switch residing on
相关PDF资料 |
PDF描述 |
|---|---|
| V24C28H100B3 | CONVERTER MOD DC/DC 28V 100W |
| HMM36DRTH | CONN EDGECARD 72POS DIP .156 SLD |
| EBM18DRKS | CONN EDGECARD 36POS DIP .156 SLD |
| V24C28H100B2 | CONVERTER MOD DC/DC 28V 100W |
| V24C48H100BG3 | CONVERTER MOD DC/DC 48V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4217 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
| LTC4217CDHC | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
| LTC4217CDHC#PBF | 功能描述:IC CTRLR HOT SWAP 2A 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4217CDHC#TRPBF | 功能描述:IC CTRLR HOT SWAP 2A 16-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC4217CDHC-12 | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。