- 您现在的位置：买卖IC网 > PDF目录79679 > LTC4217CDHC#TRPBF (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 PDF资料下载
参数资料
| 型号： | LTC4217CDHC#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO16 |
| 封装： | 5 X 3 MM, LEAD FREE, PLASTIC, MO-229WJED-1, DFN-16 |
| 文件页数： | 4/18页 |
| 文件大小： | 238K |
| 代理商： | LTC4217CDHC#TRPBF |
LTC4217
12
4217fe
applicaTions inForMaTion
a resistor between the ISET pin and ground. As shown in
the Functional Diagram the voltage at the ISET pin (via
the clamp circuit) sets the CS amplifier’s built-in offset
voltage. This offset voltage directly determines the active
current limit value. With the ISET pin open, the voltage at
the ISET pin is determined by a positive temperature co-
efficient reference. This voltage is set to 0.618V at room
temperature which corresponds to a 2A current limit at
room temperature.
AnexternalresistorplacedbetweentheISETpinandground
forms a resistive divider with the internal 20k sourcing
resistor. The divider acts to lower the voltage at the ISET
pin and therefore lower the current limit threshold. The
overall current limit threshold precision is reduced to
±16% when using a 20k resistor to halve the threshold.
Using a switch (connected to ground) in series with this
external resistor allows the active current limit to change
only when the switch is closed. This feature can be used
when the start-up current exceeds the typical maximum
load current.
Monitor MOSFET Temperature
The voltage at the ISET pin increases linearly with increas-
ing temperature. The temperature profile of the ISET pin is
shown in the Typical Performance Characteristics section.
Using a comparator or ADC to measure the ISET voltage
provides an indicator of the MOSFET temperature.
There is an overtemperature circuit in the LTC4217 that
monitors an internal voltage similar to the ISET pin voltage.
When the die temperature exceeds 145°C the circuit turns
off the MOSFET until the temperature drops to 125°C.
Monitor MOSFET Current
ThecurrentintheMOSFETpassesthroughasenseresistor.
The voltage on the sense resistor is converted to a cur-
rent that is sourced out of the IMON pin. The gain of ISENSE
amplifier is 50A/A from IMON for 1A of MOSFET current.
This output current can be converted to a voltage using an
external resistor to drive a comparator or ADC. The voltage
compliance for the IMON pin is from 0V to INTVCC – 0.7V.
A microcontroller with a built-in comparator can build a
simple integrating single-slope ADC by resetting a capaci-
tor that is charged with this current. When the capacitor
voltage trips the comparator and the capacitor is reset, a
timer is started. The time between resets will indicate the
MOSFET current.
Monitor OV and UV Faults
Protecting the load from an overvoltage condition is
the main function of the OV pin. In the LTC4217-12, an
internal resistive divider (driving the OV pin) connects
to a comparator to turn off the MOSFET when the VDD
voltage exceeds 15.05V. If the VDD pin subsequently falls
back below 14.8V, the switch will be allowed to turn on
immediately. In the LTC4217 the OV pin threshold is 1.23V
when rising, and 1.21V when falling out of overvoltage.
The UV pin functions as an undervoltage protection pin or
as an “ON” pin. In the LTC4217-12 the MOSFET turns off
when VDD falls below 9.23V. If the VDD pin subsequently
rises above 9.88V for 100ms, the switch will be allowed
to turn on again. The LTC4217 UV turn-on/off thresholds
are 1.23V (rising) and 1.15V (falling).
InthecasesofanundervoltageorovervoltagetheMOSFET
turns off and there is indication on the PG status pin. When
the overvoltage is removed the MOSFET’s gate ramps up
immediately at the rate determined by the INRUSH block.
Power Good Indication
In addition to setting the foldback current limit threshold,
the FB pin is used to determine a power good condition.
The LTC4217-12 uses an internal resistive divider on the
OUT pin to drive the FB pin. The PG comparator indicates
logic high when OUT pin rises above 10.5V. If the OUT pin
subsequentlyfallsbelow10.3Vthecomparatortoggleslow.
On the LTC4217 the PG comparator drives high when the
FB pin rises above 1.23V and low when falls below 1.21V.
Once the PG comparator is high the GATE pin voltage is
monitored with respect to the OUT pin. Once the GATE
minus OUT voltage exceeds 4.2V the PG pin goes high.
This indicates to the system that it is safe to load the OUT
pin while the MOSFET is completely turned “on”. The PG
pin goes low when the GATE is commanded off (using
the UV, OV or SENSE pins) or when the PG comparator
drives low.
相关PDF资料 |
PDF描述 |
|---|---|
| LPQ142-CF | 4-OUTPUT 145 W AC-DC PWR FACTOR CORR MODULE |
| LHR4301-2 | 1-OUTPUT 14.4 W AC-DC REG PWR SUPPLY MODULE |
| LES020ZG-3N1N92H | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES020ZG-3N1N93H | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES020ZG-3NN92V | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4217CFE | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
| LTC4217CFE#PBF | 功能描述:IC CTRLR HOT SWAP 2A 20-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4217CFE#TRPBF | 功能描述:IC CTRLR HOT SWAP 2A 20-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC4217CFE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
| LTC4217CFE-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:2A Integrated Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。