- 您现在的位置：买卖IC网 > PDF目录22128 > LTC4240IGN#PBF (Linear Technology)IC CTRLR HOTSWAP CPCI I2C 28SSOP PDF资料下载
参数资料
| 型号： | LTC4240IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 24/28页 |
| 文件大小： | 493K |
| 描述： | IC CTRLR HOTSWAP CPCI I2C 28SSOP |
| 标准包装： | 49 |
| 类型： | 热交换控制器 |
| 应用： | CompactPCI? |
| 内部开关： | 无 |
| 电源电压： | 3.3V，5V，±12V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页
LTC4240
24
4240f
PRSNT1#
PRSNT2#
Expansion Configuration
Open
Open
No plug in board present
Ground
10k Pull-Up
Plug-in board present,
maximum power consumption
10k Pull-Up
Ground
Plug-in board present,
nominal power consumption
Ground
Ground
Plug-in board present,
minimum power consumption
Other CompactPCI Applications
If no 3.3V supply input is required, Figure 15 illustrates
how the LTC4240 should be configured.
For applications where the BD_SEL# connector pin is
grounded on the backplane, the circuit in Figure 16 allows
the LTC4240 to be reset simply by pressing a pushbutton
switch on the CPCI plug-in board. This arrangement
allows for manual resetting of the LTC4240s circuit break-
ers.
Input Transient Protection
Hot-plugging a board into a backplane generates inrush
currents from the backplane power supplies. This is due to
the charging of the plug-in board bulk capacitance. To
reduce this transient current to a safe level, the CPCI Hot
Swap specification restricts the amount of unswitched
capacitance used on the input side of the plug-in board.
Each pin connected to the CPCI female connector on the
plug-in board is allowed at most 0.01礔/pin. Bulk capaci-
tors are only allowed on the switched output side of the
LTC4240 (5V
OUT
, 3V
OUT
, 12V
OUT
, V
EEOUT
). Some bulk
capacitance is allowed on the Early Power planes, but only
because a current limiting resistor is assumed to separate
the connector from the bulk capacitor. Circuits normally
placed on the unswitched Early Power (PCI Bridge, for
example) need to have a current limiting resistor.
APPLICATIO S I FOR ATIO
U
U
U
The assumption by the CompactPCI specification is that
there is a diode to 3.3V on the circuit that is driving the
BD_SEL# pin. The 1.2k resistor pull up to 5V
IN
on the plug-
in card will thus be clamped by the diode to 3.3V. If the
BD_SEL# pin is being driven high, the actual voltage on the
pin will be approximately 3.9V. This is still above the high
TTL threshold of the LTC4240 OFF/ON pin, but low enough
for Q4 to disable the bus switches and thus remove the 10k
resistors from the I/O lines. Note that BD_SEL# is ordi-
narily connected to V(I/O), which in turn is allowed to be
driven by either 3.3V or 5V. For applications such as
shown in Figure 14, the pull up on BD_SEL# is restricted
to the long 5V pins. A bus switch with no internal diode to
V
DD
is preferred. Since the power to the bus switch is
derived from one of the unswitched power planes, a 100&
resistor plus a 0.1礔 bypass capacitor should be placed in
series with its power supply.
When the plug-in card is removed from the connector, the
BD_SEL# connection is broken first, and the BD_SEL#
voltage pulls up to 5V. This causes Q4 to turn off, which re-
enables the bus switch, and the precharge resistors are
again connected to the LTC4240 PRECHARGE pin for the
remainder of the board extraction process.
The LTC4240 BE pin can alternatively be used to drive the
enable input of the bus switch. The BE signal would then
keep the I/O lines precharged until all supplies reached
power good status. The resistor in series with the
PRECHARGE pin protects the internal circuitry from large
voltage transients during live insertion.
PRSNT1#, PRSNT2#
PRSNT1# and PRSNT2# are PCI signals that convey the
plug-in boards power consumption information. These
pins should either be shorted to ground or be connected
to Early Power with a 10k resistor. The voltage levels (TTL)
at the PRSNT#1, 2 pins can be read using the I
2
C 2-wire
interface.
相关PDF资料 |
PDF描述 |
|---|---|
| M4A3-32/32-7VNI | IC CPLD ISP 4A 32MC 44TQFP |
| LTC1643AHIGN | IC CTRLR HOTSWAP PCI BUS 16SSOP |
| TPSE227K010R0050 | CAP TANT 220UF 10V 10% 2917 |
| EEC25DTEF | CONN EDGECARD 50POS .100 EYELET |
| TAP475M010SLZ | CAP TANT 4.7UF 10V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4241 | 制造商:LINER 制造商全称:Linear Technology 功能描述:PCI-Bus with 3.3V Auxiliary Hot Swap Controller |
| LTC4241CGN | 功能描述:IC CTRLR HOTSWAP PCI 3.3V 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4241CGN#PBF | 功能描述:IC CTRLR HOTSWAP CPCI I2C 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4241CGN#TR | 功能描述:IC CTRLR HOTSWAP 3.3V AUX 20SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4241CGN#TRPBF | 功能描述:IC PCI-BUS W/HOT SWAP 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。