- 您现在的位置：买卖IC网 > PDF目录22130 > LTC4244IGN-1#TR (Linear Technology)IC CTRLR HOT SWAP CPCI 20-SSOP PDF资料下载
参数资料
| 型号： | LTC4244IGN-1#TR |
| 厂商： | Linear Technology |
| 文件页数： | 12/28页 |
| 文件大小： | 337K |
| 描述： | IC CTRLR HOT SWAP CPCI 20-SSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | CompactPCI? |
| 内部开关： | 无 |
| 电源电压： | 3.3V，5V，±12V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
12
LTC4244/LTC4244-1
42441f
" 5V
IN
UVL Threshold Voltage: The LTC4244s 5V
IN
UVL
threshold voltage is 4.25V vs. 2.5V for the LTC1644.
" V
EEOUT
PWRGD Threshold Voltage: The LTC4244 V
EEOUT
power good threshold voltage is 11.1V vs 10.5V for
the LTC1644.
" Absolute Maximum Ratings: The LTC4244s absolute
maximum ratings for the 12V
IN
and V
EEIN
pins are
?4.4V, respectively, vs ?3.2V for the LTC1644.
" 5V/3.3V Circuit Breakers: If a short-circuit occurs after
power-up, the LTC4244 actively limits the voltage
dropped across the external 5V and 3.3V sense resis-
tors to 150mV for 25祍 before tripping the circuit
breaker. In the event either the 5V or 3.3V sense resistor
voltage exceeds 150mV, the LTC1644 trips the circuit
breaker without delay.
" 5V/3.3V Circuit Breaker Threshold Voltage: The LTC4244
threshold voltage is 52mV ?mV vs 55mV ?5mV for
the LTC1644.
" External Gate Voltage: After power-up, the voltage drop
from the 12V
IN
pin to the GATE pin is 0.6V for the
LTC4244 vs 50mV for the LTC1644.
Hot Plug Power-Up Sequence
The LTC4244 is specifically designed for hot plugging
CPCI boards. The typical application circuit is shown in
Figure 1.
CPCI Connector Pin Sequence
The staggered lengths of the CPCI male connector pins
ensure that all power supplies are physically connected to
the LTC4244 before back-end power is allowed to ramp up
(BD_SEL# asserted low). The long pins, which include 5V,
3.3.V, V(I/O) and GND, mate first. The short BD_SEL# pin
mates last. At least one long 5V power pin must be
connected to the LTC4244 in order for the PRECHARGE
voltage to be available during the insertion sequence.
The following is a typical hot insertion sequence:
1. ESD clips make contact.
2. Long power and ground pins make contact and Early
Power is established. The 1V precharge voltage be-
comes valid at this stage of insertion. Power is also
applied to the pull-up resistors connected to the FAULT,
PWRGD and OFF/ON pins. All power switches are held
off at this stage of insertion.
3. Medium length pins make contact. Both FAULT and
PWRGD continue to be pulled up high at this stage in the
hot plug sequence, and the power switches are still held
off. The 12V and 12V connector pins also make
contact at this stage. Zener clamps Z1 and Z2 plus shunt
RC snubbers R16-C5 and R15-C4 help protect the V
EEIN
and 12V
IN
pins, respectively, from large voltage tran-
sients during hot insertion.
The signal pins also connect at this point. These include
the HEALTHY# signal (which is connected to the PWRGD
pin), the PCI_RST# signal (which is connected to the
RESETIN pin) and the I/O connector pins (which are
biased at 1V by the LTC4244s precharge circuit).
4. Short pins make contact. The BD_SEL# signal is con-
nected to the OFF/ON pin. If the BD_SEL# signal is
grounded on the backplane, the plug-in card power-up
cycle begins immediately. System backplanes that do
not ground the BD_SEL# signal will instead have cir-
cuitry that detects when BD_SEL# makes contact with
the plug-in board. The system logic can then control the
power up process by pulling BD_SEL# low.
Power-Up Sequence
The back-end 3.3V
OUT
and 5V
OUT
power planes are iso-
lated from the 3.3V
IN
and 5V
IN
power planes by external
N-channel pass transistors Q1 and Q2, respectively. Inter-
nal pass transistors isolate the back-end 12V
OUT
and
V
EEOUT
power planes from the 12V
IN
and V
EEIN
power
planes.
APPLICATIO S I FOR ATIO
U
U
U
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1643AHIGN#TR | IC CTRLR HOTSWAP PCI BUS 16SSOP |
| RBM06DCBD | CONN EDGECARD 12POS R/A .156 SLD |
| B280-13-F | DIODE SCHOTTKY 2A 80V SMB |
| LTC1643ALIGN#TRPBF | IC CTRLR HOTSWAP PCI BUS 16SSOP |
| R2S8-2424/P | CONV DC/DC 2W 24VIN 24VOUT SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4244IGNTR | 制造商:Linear Technology 功能描述: |
| LTC4245 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Supply Hot Swap Controller for Advanced Mezzanine Card |
| LTC4245CG | 制造商:LINER 制造商全称:Linear Technology 功能描述:Multiple Supply Hot Swap Controller with I2C Compatible Monitoring |
| LTC4245CG#PBF | 功能描述:IC CNTRLR HOT SWAP 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4245CG#TRPBF | 功能描述:IC CNTRLR HOT SWAP 36-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。