- 您现在的位置：买卖IC网 > PDF目录19717 > LTC4253AIGN#PBF (Linear Technology)IC HOT SWAP CONTRLR -48V 16-SSOP PDF资料下载
参数资料
| 型号： | LTC4253AIGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/34页 |
| 文件大小： | 383K |
| 描述： | IC HOT SWAP CONTRLR -48V 16-SSOP |
| 标准包装： | 100 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 8.2 V ~ 14.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC4253/LTC4253A
14
425353aff
For more information www.linear.com/4253
APPLICATIONS INFORMATION
OPERATION
Higher overloads are handled by an analog current limit
loop. If the drop across R
S
reaches V
ACL
, the current
limiting loop servos the MOSFET gate and maintains a
constant output current of V
ACL
/R
S
. In current limit mode,
V
OUT
(MOSFET drain-source voltage drop) typically rises
and this increases MOSFET heating. If V
OUT
> V
DRNCL
,
connecting an external resistor, R
D
between V
OUT
and
DRAIN allows the fault timing cycle to be shortened by
accelerating the charging of the TIMER capacitor. The
TIMER pull-up current is increased by 8 " I
DRN
. Note that
because SENSE > 50mV , TIMER charges C
T
during this
time, and the LTC4253/LTC4253A eventually shut down.
Low impedance failures on the load side of the LTC4253/
LTC4253A, coupled with 48V or more driving potential,
can produce current slew rates well in excess of 50A/祍.
Under these conditions, overshoot is inevitable. A fast
SENSE comparator with a threshold of 200mV detects
overshoot and pulls GATE low much harder and hence
much faster than the weaker current limit loop. The V
ACL
/
R
S
current limit loop then takes over and servos the cur-
rent as previously described. As before, TIMER runs and
shuts down the LTC4253/LTC4253A when C
T
reaches 4V .
If C
T
reaches 4V , the LTC4253/LTC4253A latch off with a
5礎 pull-up current source. The LTC4253/LTC4253A circuit
breaker latch is reset by either pulling the RESET pin active
high until TIMER goes low, pulling UV momentarily low,
dropping the input voltage V
IN
below the internal UVLO
threshold or pulsing TIMER momentarily low with a switch.
Although short-circuits are the most obvious fault type,
several operating conditions may invoke overcurrent
protection. Noise spikes from the backplane or load, input
steps caused by the connection of a second, higher voltage
supply, transient currents caused by faults on adjacent
circuit boards sharing the same power bus or the insertion
of non-hot swappable products could cause higher than
anticipated input current and temporary detection of an
overcurrent condition. The action of TIMER and C
T
rejects
these events allowing the LTC4253/LTC4253A to ride out
temporary overloads and disturbances that could trip a
simple current comparator and, in some cases, blow a fuse.
pins, the area in and around the LTC4253 and all associ-
ated components should be free of any other planes such
as chassis ground, return, or secondary-side power and
ground planes.
V
IN
may be biased with additional current up to 30mA, to
accomodate external loading such as the PWRGD opto-
couplers shown in Figure 2. As an alternative to running
higher current, simply buffer V
IN
with an emitter follower
as shown in Figure 3. A method that cascodes the PWRGD
outputs as shown in Figure 17.
V
IN
is rated to handle 30mA within the thermal limits of
the package, and is tested to survive a 100祍, 100mA
SHUNT REGULATOR
A fast responding shunt regulator clamps the V
IN
pin to
13V (V
Z
). Power is derived from 48RTN by an external
current limiting resistor, R
IN
. A 1礔 decoupling capacitor,
C
IN
filters supply transients and contributes a short delay
at start-up.
To meet creepage requirements R
IN
may be split into two
or more series connected units. This introduces a wider
total spacing than is possible with a single component
while at the same time ballasting the potential across the
gap under each resistor. The LTC4253 is fundamentally a
low voltage device that operates with 48V as its reference
ground. To further protect against arc discharge into its
相关PDF资料 |
PDF描述 |
|---|---|
| MIC3775-1.5BMM | IC REG LDO 1.5V .75A 8-MSOP |
| EYM06DRST | CONN EDGECARD 12POS DIP .156 SLD |
| 191-015-223R001 | CONN DB15 FMALE VERT PRESFIT SLD |
| EGM06DRST | CONN EDGECARD 12POS DIP .156 SLD |
| EMC50DREH-S93 | CONN EDGECARD 100POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4253BCGN#PBF | 功能描述:IC HOT SWAP CONTROLLER 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4253BCGN#PBF | 制造商:Linear Technology 功能描述:HOT SWAP CONTROLLER -48V SSOP-16 |
| LTC4253BCGN#TRPBF | 功能描述:IC HOT SWAP CONTROLLER 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC4253BIGN#PBF | 功能描述:IC HOT SWAP CONTROLLER 16SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4253BIGN#PBF | 制造商:Linear Technology 功能描述:HOT SWAP CONTROLLER -48V SSOP-16 |
发布紧急采购，3分钟左右您将得到回复。