- 您现在的位置：买卖IC网 > PDF目录44996 > LTC4259CGW (LINEAR TECHNOLOGY CORP) 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 PDF资料下载
参数资料
| 型号： | LTC4259CGW |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封装： | 0.300 INCH, PLASTIC, SSOP-36 |
| 文件页数： | 7/32页 |
| 文件大小： | 324K |
| 代理商： | LTC4259CGW |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC4259
15
4259i
17k and 29k (between 19k and 26.5k guaranteed) as a
valid PD and report Detect Good (100 binary) in the Detect
Status bits (bits 2 through 0) of the corresponding Port
Status register. Values outside this range, including open
and short circuits, are also reported in the Detect Status
bits. Refer to Table 1 for a complete decoding of the Detect
Status bits.
The first test point is taken by forcing a test current into
the port, waiting a short time to allow the line to settle and
measuring the resulting voltage. This result is stored and
the second current is applied to the port, allowed to settle
and the voltage measured. Each point takes 100ms to
measure, and an entire detection cycle takes 200ms.
The port’s operating mode controls if and when the
LTC4259 runs a detection cycle. In manual mode, the port
will sit idle until a Restart Detection (register 18h) com-
mand is received. It will then run a complete 200ms
detection cycle on the selected port, report the results in
the Detect Status bits in the corresponding Port Status
register and return to idle until another command is
received. In Semiauto mode, the LTC4259 autonomously
tests valid PDs connected to the ports but it will not apply
power until instructed to do so by the host controller. It
repeatedly queries the port every 320ms and updates the
Detect Status bits at the end of each cycle. If a Detect Good
is reported, it will advance to the classification phase and
report that result in the Port Status register. Until in-
structed to do otherwise, the LTC4259 will continue to
repeat detection on the port. Behavior in Auto mode is
similar to Semiauto; however, after a Detect Good is
reported, the LTC4259 performs the classification phase
and then powers up the port without further intervention.
The signature detection circuitry is disabled when the port
is in Shutdown mode, powered up or the corresponding
Detect Enable bit is cleared.
CLASSIFICATION
A PD has the option of presenting a “classification signa-
ture” to the PSE to indicate how much power it will draw
when powered up. This signature consists of a specific
constant current draw when the PSE port voltage is between
15.5V and 20.5V, with the current level indicating the power
class to which the PD belongs. Per the IEEE 802.3af speci-
fication, the LTC4259 identifies the five classes of PD listed
in Table 2. Note that class 4 is presently specified by the IEEE
as reserved for future use but it is intended to be used with
PDs that digitally communicate additional requirements
over the Ethernet interface after being powered. Figure 14
shows a PD load line, starting with the shallow slope of the
25k signature resistor below 10V then drawing the proper
current for class 3 between 15V and 20V. The LTC4259’s
load line for classification is also shown in Figure 14. It has
low impedance until current limit at 65mA (typ).
APPLICATIO S I FOR ATIO
WU
UU
Figure 13. PD Detection
Table 2. IEEE 802.3af Powered Device Classes
IEEE 802.3fa
CLASSIFICATION
MAXIMUM
CLASS
CURRENT
PD POWER
CLASS DESCRIPTION
0
0mA to 4mA
12.95W
Unknown PD Power, PD Does Not Implement Classification
1
9mA to 12mA
3.84W
Low Power PD
2
17mA to 20mA
6.49W
Medium Power PD
3
26mA to 30mA
12.95W
High or Full Power PD
4
36mA to 44mA
12.95W
Reserved, Power as Class O
FIRST
DETECTION
POINT
SECOND
DETECTION
POINT
VALID PD
25k
SLOPE
275
165
CURRENT
(
A)
0V-2V
OFFSET
VOLTAGE
4259 F13
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4267CGN-1#TR | 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC4267IGN-1 | 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC4267CGN-1 | 1 A SWITCHING CONTROLLER, 240 kHz SWITCHING FREQ-MAX, PDSO16 |
| LTC4270BIUKG#TRPBF | SPECIALTY ANALOG CIRCUIT, PQCC52 |
| LTC4270BIUKG#PBF | SPECIALTY ANALOG CIRCUIT, PQCC52 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4259CGW-ES | 制造商:LINEAR_TECH 功能描述: |
| LTC4260 | 制造商:LINER 制造商全称:Linear Technology 功能描述:UV, OV and Reverse Supply Protection Controller Low Operating Current: 125μA |
| LTC4260CGN | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 24-Pin SSOP N |
| LTC4260CGN#PBF | 功能描述:IC CTLR HOT SWAP I2C 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4260CGN#TR | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 24-Pin SSOP N T/R |
发布紧急采购，3分钟左右您将得到回复。