- 您现在的位置：买卖IC网 > PDF目录22106 > LTC4260CSW#PBF (Linear Technology)IC CTLR HOT SWAP I2C 24-SOIC PDF资料下载
参数资料
| 型号： | LTC4260CSW#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/30页 |
| 文件大小： | 295K |
| 描述： | IC CTLR HOT SWAP I2C 24-SOIC |
| 标准包装： | 32 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 8.5 V ~ 80 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1342 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC4260
13
4260fc
For more information www.linear.com/LTC4260
applicaTions inForMaTion
As the SOURCE voltage rises, so will the FB pin which
is monitoring it. If the voltage across the current sense
resistor R
S
gets too high, the inrush current will then be
limited by the internal current limit circuitry. Once the FB
pin crosses its 3.5V threshold, the GPIO pin, in its default
configuration, will cease to pull low and indicate that the
power is now good.
Turn-Off Sequence
The switch can be turned off by a variety of conditions.
A normal turn-off is initiated by the ON pin going low or
a serial bus turn-off command. Additionally, several fault
conditions will turn off the switch. These include an input
overvoltage (OV pin), input undervoltage (UV pin), over-
current circuit breaker (SENSE pin) or BD錚RST going
high. Writing a logic one into the UV, OV or overcurrent
fault bits will also turn off the switch if their autoretry bits
are set to false.
Normally the switch is turned off with a 1mA current pulling
down the GATE pin to ground. With the switch turned off,
the SOURCE voltage drops and when the FB pin crosses
below its threshold, GPIO pulls low to indicate that the
output power is no longer good.
If the V
DD
pin falls below 7.5V for greater than 5祍 or INTV
CC
drops below 3.8V for greater than 1祍, a fast shutdown of
the switch is initiated. The GATE pin is pulled down with
a 600mA current to the SOURCE pin.
V
DD
+ 13V
V
DD
4260 F02
t
1
t
2
GATE
V
OUT
SLOPE = 18礎/C1
Figure 2. Supply Turn-On
Overcurrent Fault
The LTC4260 features an adjustable current limit with fold-
back that protects against short circuits or excessive load
current. To protect against excessive power dissipation in
the switch during active current limit, the available current
is reduced as a function of the output voltage sensed by
the FB pin. The device also features a variable overcurrent
response time. A graph in the Typical Performance curves
shows the delay from a voltage step at the SENSE pin until
the GATE voltage starts falling, as a function of overdrive.
An overcurrent fault occurs when the current limit circuitry
has been engaged for longer than the time-out delay set by
the TIMER pin. Current limiting begins when the current
sense voltage between the V
DD
and SENSE pins reaches
20mV to 50mV (depending on the foldback). The GATE
pin is then brought down with a 600mA GATE-to-SOURCE
current. The voltage on the GATE is regulated in order
to limit the current sense voltage to less than 50mV. At
this point, a circuit breaker time delay starts by charging
the external timing capacitor from the TIMER pin with a
100礎 pull-up current. If the TIMER pin reaches its 1.2V
threshold, the external switch turns off (with a 1mA cur-
rent from GATE to ground). The overcurrent present bit,
C2, and the overcurrent fault bit, D2, are set at this time.
The circuit breaker time delay is given by:
t
CB
= C
T
" 12 [ms/礔]
After the switch is turned off, the TIMER pin begins
discharging the timing capacitor with a 2礎 pull-down
current. When the TIMER pin reaches its 0.2V threshold,
the overcurrent present bit, C2, is cleared, and the switch
will be allowed to turn on again if the overcurrent fault has
been cleared. However, if the overcurrent autoretry bit, A2,
has been set then the switch turns on again automatically
(without resetting the overcurrent fault). Use a minimum
value of 0.1nF for C
T
.
The waveform in Figure 3 shows how the output latches
off following a short circuit. The drop across the sense
resistor is held at 20mV as the timer ramps up.
相关PDF资料 |
PDF描述 |
|---|---|
| 1-119738-6 | CONN HOUSING 30 DUAL POS GOLD |
| TAP104M035SCS | CAP TANT 0.1UF 35V 20% RADIAL |
| TC1264-1.8VDB | IC REG LDO 1.8V .8A SOT223-3 |
| ADM1075-1ACPZ | IC HOT SWAP CTRLR -48V 28LFCSP |
| VI-23F-EV-F1 | CONVERTER MOD DC/DC 72V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4260CUH | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 32-Pin QFN EP |
| LTC4260CUH#PBF | 功能描述:IC CTLR HOT SWAP I2C 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4260CUH#TRPBF | 功能描述:IC HOT SWAP CNTRL I2C 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4260IGN | 制造商:LINER 制造商全称:Linear Technology 功能描述:Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
| LTC4260IGN#PBF | 功能描述:IC CTLR HOT SWAP I2C 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。