- 您现在的位置：买卖IC网 > PDF目录20101 > LTC4260IGN#PBF (Linear Technology)IC CTLR HOT SWAP I2C 24-SSOP PDF资料下载
参数资料
| 型号： | LTC4260IGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/30页 |
| 文件大小： | 295K |
| 描述： | IC CTLR HOT SWAP I2C 24-SSOP |
| 标准包装： | 55 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 8.5 V ~ 80 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 24-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1342 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC4260
14
4260fc
For more information www.linear.com/LTC4260
During a short circuit, if the current limit sense voltage
exceeds 150mV, the active current limit enters a high cur-
rent protection mode that immediately turns off the output
transistor by pulling the GATE-to-SOURCE voltage to zero.
Current in the output transistor drops from tens of amps
to zero in a few hundred nanoseconds. The input voltage
will drop during the high current and then spike upwards
due to parasitic inductances when the FET shuts off (see
Supply Transients). Following this event, the part may turn
on again after a delay (typically the 100ms normal turn-on
delay if the input voltage drops below the UVLO threshold)
and enters active current limit before shutting off.
Overvoltage Fault
An overvoltage fault occurs when the OV pin rises above
its 3.5V threshold. This shuts off the switch immediately
(with a 1mA current from GATE to ground) and sets the
overvoltage present bit, C0, and the overvoltage fault
bit D0. If the OV pin subsequently falls back below the
threshold for 100ms, the switch will be allowed to turn on
again unless the overvoltage autoretry has been disabled
by clearing bit A0.
Undervoltage Fault
An undervoltage fault occurs when the UV pin falls below
its 3.12V threshold. This turns off the switch immediately
(with a 1mA current from GATE to ground) and sets the
undervoltage present bit, C1, and the undervoltage fault
bit D1. If the UV pin subsequently rises above the thresh-
old for 100ms, the switch will turn on again unless the
applicaTions inForMaTion
V
OUT
50V/DIV
I
OUT
5A/DIV
V
GATE
10V/DIV
TIMER
2V/DIV
100祍/DIV
4260 F03
Figure 3. Short-Circuit Waveforms
undervoltage autoretry has been disabled by clearing bit
A1. When power is applied to the device, if UV is below its
3.12V threshold after INTV
CC
crosses its 4.5V undervoltage
lockout threshold, an undervoltage fault will be logged in
the fault register.
Board Present Change of State
Whenever the BD錚RST pin toggles, bit D4 is set to
indicate a change of state. When the BD錚RST pin goes
high, indicating board removal, the switch turns off im-
mediately (with a 1mA current from GATE to ground) and
clears the board present bit, C4. If the BD錚RST pin is
pulled low, indicating a board insertion, all fault bits except
D4 will be cleared and the board present bit, C4, is set. If
the BD錚RST pin remains low for 100ms the state of the
ON pin will be captured in the FET On Control bit A3. This
turns the switch on if the ON pin is tied high. There is an
internal 10礎 pull-up current source on the BD錚RST pin.
If the system shuts down due to a fault, it may be desirable
to restart the system simply by removing and reinserting
a load card. In cases where the LTC4260 and the switch
reside on a backplane or midplane and the load resides
on a plug-in card, the BD錚RST pin can be used to detect
when the plug-in card is removed (see Figure 4). Once
the plug-in card is reinserted the fault register is cleared
(except for D4). After 100ms the state of the ON pin is
latched into bit A3 of the control register. At this point the
system will start up again.
If a connection sense on the plug-in card is driving the
BD錚RST pin, the insertion or removal of the card may
cause the pin voltage to bounce. This will result in clear-
ing the fault register when the card is removed. The pin
can be debounced using a filter capacitor, C
BD錚RST
, on
the BD錚RST pin as shown in Figure 4. The filter time
is given by:
t
FILTER
= C
BD錚RST
" 123 [ms/礔]
FET Short Fault
A FET short fault will be reported if the data converter
measures a current sense voltage greater than or equal
to 2mV while the FET is turned off. This condition sets the
FET short present bit, C5, and the FET short fault bit D5.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23N-CX-F3 | CONVERTER MOD DC/DC 18.5V 75W |
| 2A03G-T | RECTIFIER GPP 200V 2.0A DO-15 |
| EBM10DCAI-S189 | CONN EDGECARD 20POS R/A .156 SLD |
| VI-23N-CX-F2 | CONVERTER MOD DC/DC 18.5V 75W |
| GRM0335C1E820JD01D | CAP CER 82PF 25V 5% NP0 0201 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4260ISW | 制造商:LINER 制造商全称:Linear Technology 功能描述:Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring |
| LTC4260ISW#PBF | 功能描述:IC HOT SWAP CNTRL I2C 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4260ISW#TRPBF | 功能描述:IC HOT SWAP CNTRL I2C 24-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4260IUH | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 80V 32-Pin QFN EP |
| LTC4260IUH#PBF | 功能描述:IC HOT SWAP CNTRL I2C 32-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。