- 您现在的位置：买卖IC网 > PDF目录22109 > LTC4261IGN#TRPBF (Linear Technology)IC CTRLR HOTSWAP W/ADC 28-SSOP PDF资料下载
参数资料
| 型号： | LTC4261IGN#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 12/34页 |
| 文件大小： | 361K |
| 描述： | IC CTRLR HOTSWAP W/ADC 28-SSOP |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 9 V ~ 11.2 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC4261/LTC4261-2
12
42612fc
The LTC4261/LTC4261-2 are designed to turn a boards
supply voltage on and off in a controlled manner, allowing
the board to be safely inserted or removed from a live 48V
backplane. The devices also feature an onboard 10-bit ADC
and I
2
C interface that allows monitoring board current,
voltages and faults. The main functional circuits of the
LTC4261/LTC4261-2 are illustrated in the Block Diagram.
In normal operation after a start-up debounce delay, the
GATE pin turns on the external N-channel FET passing
power to the load. The GATE pin is powered by a shunt
regulated 11.2V supply on the V
IN
pin that is derived
from 48V RTN through a dropping resistor. The turn-on
sequence starts by pulling the SS pin up. The voltage at
the SS pin is converted to a current, I
GATE(UP)
, pulling the
GATE up. When the pass FET starts to turn on and charge
the load capacitor, the inrush current flowing through the
FET is a function of the capacitor at RAMP (C
R
), the load
capacitor (C
L
) and the ramp current (I
RAMP
) that flows
from the RAMP pin to C
R
:
I
INRUSH
=I
RAMP
C
L
C
R
I
RAMP
and I
GATE(UP)
are approximately proportional to
the SS pin voltage and are limited to 20礎 and 11.5礎,
respectively when SS reaches its clamping voltage (2.56V).
The ACL amplifier is used for overcurrent and short-circuit
protection. It monitors the load current through the SENSE
pin voltage and a sense resistor R
S
. In an overcurrent
condition, the ACL amplifier limits the current to 50mV/
R
S
by pulling down GATE in an active servo loop. After a
530祍 timeout, the ACL amplifier turns off the pass FET .
In the event of a catastrophic short circuit, when V
SENSE
crosses 250mV , a fast response comparator immediately
pulls the GATE pin down.
The DRAIN and the GATE voltages are monitored to de-
termine if power is available for the load. Two power good
signals are sequenced on the PG pin (first power good
signal) and the PGIO pin (second power good signal), each
with a debounce delay that is twice the start-up delay. The
PGIO pin can also be used as a general purpose input or
output. The PGI pin serves as a watchdog to monitor the
output of the DC/DC module. If the module output fails to
come up, the LTC4261/LTC4261-2 shut down.
The TMR pin generates delays for initial start-up, auto-
retry following a fault, power good outputs and PGI check.
The logic circuits a re powered by an internally generated
5V supply (available on the INTV
CC
pin). Prior to turning
on the pass FET , both V
IN
and INTV
CC
voltages must ex-
ceed their undervoltage lockout thresholds. In addition,
the control inputs UVH, UVL, OV , EN, ON and PGI are
monitored by comparators. The FET is held off until all
start-up conditions are met.
A 10-bit analog-to-digital converter (ADC) is included in the
LTC4261/LTC4261-2. The ADC measures SENSE resistor
voltage as well as voltage at the ADIN2/OV (SSOP/QFN)
and ADIN pins. The results are stored in on-board registers.
An I
2
C interface is provided to read the ADC data registers.
It also allows the host to poll the device and determine if a
fault has occurred. If the ALERT line is used as an interrupt,
the host can respond to a fault in real time. The SDA line
is divided into SDAI (input) and SDAO (output) to facili-
tate opto coupling with the system host. Two three-state
pins, ADR0 and ADR1, are used to decode eight device
addresses. The interface can also be configured through
the ADR0 and ADR1 pins for a single-wire broadcast
mode, sending ADC data and faults status through the
SDAO pin to the host without clocking the SCL line. This
single-wire, one-way communication simplifies system
design by eliminating two optocouplers on SCL and SDAI
that are required by an I
2
C interface.
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| VI-B2Y-CW-F1 | CONVERTER MOD DC/DC 3.3V 66W |
| R05P212S/R6.4 | CONV DC/DC 2W 05VIN 12VOUT |
| TAP334K050SRW | CAP TANT 0.33UF 50V 10% RADIAL |
| VI-B2Y-CX-F3 | CONVERTER MOD DC/DC 3.3V 49.5W |
| R05P23.3S/R6.4 | CONV DC/DC 2W 05VIN 3.3VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4261IUFD | 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4261IUFD#PBF | 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4261IUFD#TR | 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4261IUFD#TRPBF | 功能描述:IC CTRLR HOTSWAP W/ADC 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4261IUFD-2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring |
发布紧急采购，3分钟左右您将得到回复。