- 您现在的位置：买卖IC网 > PDF目录11585 > LTC4264IDE#PBF (Linear Technology)IC CNTRLR PD INTERFACE 12-DFN PDF资料下载
参数资料
| 型号： | LTC4264IDE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC CNTRLR PD INTERFACE 12-DFN |
| 产品培训模块： | Power over Ethernet |
| 标准包装： | 91 |
| 控制器类型： | 以太网供电控制器（POE） |
| 接口： | IEEE 802.3af |
| 电流 - 电源： | 3mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 12-WFDFN 裸露焊盘 |
| 供应商设备封装： | 12-DFN（4x3） |
| 包装： | 管件 |
LTC4264
20
4264f
APPLICATIONS INFORMATION
Shutdown Interface
To disable the 25k signature resistor, connect SHDN to
the GND pin. Alternately, the SHDN pin can be driven
high with respect to VIN. Examples of interface circuits
that disable the signature and all LTC4264 functions are
shown in Figure 10, options 2 and 4. Note that the SHDN
input resistance is relatively large and the threshold volt-
age is fairly low. Because of high voltages present on the
printed circuit board, leakage currents from the GND pin
could inadvertently pull SHDN high. To ensure trouble-free
operation, use high voltage layout techniques in the vicinity
of SHDN. If unused, connect SHDN directly to VIN.
Load Capacitor
The IEEE 802.3af specication requires that the PD maintain
a minimum load capacitance of 5F. It is permissible to
have a much larger load capacitor and the LTC4264 can
charge very large load capacitors before thermal issues
become a problem. However, the load capacitor must not
be too large or the PD design may violate IEEE 802.3af
requirements. The LTC4264 maintains IEEE 802.3af com-
pliance when the load capacitor is 180F or less. A larger
capacitor can be employed in a proprietary, close-system
high power application.
If the load capacitor is too large, there can be a prob-
lem with inadvertent power shutdown by the PSE. For
example, if the PSE is running at –57V (IEEE 802.3af
maximum allowed) and the PD is detected and powered
up, the load capacitor will be charged to nearly –57V. If
for some reason the PSE voltage is suddenly reduced to
–44V (IEEE 802.3af minimum allowed), the input bridge
will reverse bias and the PD power will be supplied by the
load capacitor. Depending on the size of the load capacitor
and the DC load of the PD, the PD will not draw any power
from the PSE for a period of time. If this period of time
exceeds the IEEE 802.3af 300ms disconnect delay, the
PSE will remove power from the PD. For this reason, it is
necessary to evaluate the load current and capacitance to
ensure that inadvertent shutdown cannot occur.
Refer also to Thermal Protection in this data sheet for
further discussion on load capacitor selection.
MAINTAIN POWER SIGNATURE
In an IEEE 802.3af system, the PSE uses the maintain
power signature (MPS) to determine if a PD continues to
require power. The MPS requires the PD to periodically
draw at least 10mA and also have an AC impedance less
than 26.25k
Ω in parallel with 0.05F. If either the DC
current is less than 10mA or the AC impedance is above
26.25k
Ω, the PSE may disconnect power. The DC current
must be less than 5mA and the AC impedance must be
above 2M
Ω to guarantee power will be removed. The PD
application circuits shown in this data sheet present the
required AC impedance necessary to maintain power.
LAYOUT CONSIDERATIONS FOR THE LTC4264
The LTC4264 is relatively immune to layout problems.
Excessive parasitic capacitance on the RCLASS pin should
be avoided. Include an electrically isolated heat sink to
which the exposed pad on the bottom of the package can
be soldered. For optimum thermal performance, make the
heat sink as large as possible. Voltages in a PD can be as
large as –57V for PoE applications, so high voltage layout
techniques should be employed. The SHDN pin should
be separated from other high voltage pins, like GND and
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16F722-E/MV | IC MCU 8BIT 3.5KB FLASH 28UQFN |
| PIC16LF722-E/ML | IC PIC MCU FLASH 3.5KB 28-QFN |
| PIC16F689-E/SS | IC PIC MCU FLASH 4KX14 20SSOP |
| PIC16F685-E/SS | IC PIC MCU FLASH 4KX14 20SSOP |
| KSZ8895RQI | IC 10/100-T 5 PORT SW 128PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4265 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad IEEE 802.3at Power over Ethernet Controller |
| LTC4265CDE#PBF | 功能描述:IC CTRLR PD INTERFACE HP 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4265CDE#TRPBF | 功能描述:IC CTRLR PD INTERFACE HP 12-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC4265CDE-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:IEEE 802.3at High Power PD Interface Controller with 2-Event Classifi cation Recognition |
| LTC4265CDE-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:IEEE 802.3at High Power PD Interface Controller with 2-Event Classifi cation Recognition |
发布紧急采购，3分钟左右您将得到回复。