参数资料
| 型号： | LTC4266IGW#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/30页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR IEEE 802.3AT 36-SSOP |
| 产品培训模块： | Power over Ethernet |
| 标准包装： | 32 |
| 控制器类型： | 以太网控制器（IEEE 802.3） |
| 接口： | I²C，2 线串口 |
| 电源电压： | 3.3V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-BSOP（0.295"，7.50mm 宽） |
| 供应商设备封装： | 36-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 1338 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC4266
21
4266fd
APPLICATIONS INFORMATION
The LTC4266 will support current levels well beyond the
maximum values in the 802.3at specification. The shaded
areas in Table 5 indicate settings that may require a larger
external MOSFET, additional heat sinking, or a reduced
tLIM setting.
MOSFET Fault Detection
LTC4266 PSE ports are designed to tolerate significant
levels of abuse, but in extreme cases it is possible for
the external MOSFET to be damaged. A failed MOSFET
may short source to drain, which will make the port ap-
pear to be on when it should be off; this condition may
also cause the sense resistor to fuse open, turning off
the port but causing the LTC4266 SENSE pin to rise to
an abnormally high voltage. A failed MOSFET may also
short from gate to drain, causing the LTC4266 GATE pin
to rise to an abnormally high voltage. The LTC4266 SENSE
and GATE pins are designed to tolerate up to 80V faults
without damage.
If the LTC4266 sees any of these conditions for more than
180μs, it disables all port functionality, reduces the gate
drive pull-down current for the port and reports a FET Bad
fault. This is typically a permanent fault, but the host can
attempt to recover by resetting the port, or by resetting
the entire chip if a port reset fails to clear the fault. If the
MOSFET is in fact bad, the fault will quickly return, and
the port will disable itself again. The remaining ports of
the LTC4266 are unaffected.
An open or missing MOSFET will not trigger a FET Bad
fault, but will cause a tSTART fault if the LTC4266 attempts
to turn on the port.
Voltage and Current Readback
The LTC4266 measures the output voltage and current
at each port with an internal A/D converter. Port data is
only valid when the port power is on. The converter has
two modes:
Slow mode: 14 samples per second, 14.5 bits resolution
Fast mode: 440 samples per second, 9.5 bits resolution
In fast mode, the least significant 5 bits of the lower byte are
zeroes so that bit scaling is the same in both modes.
Disconnect
The LTC4266 monitors the port to make sure that the PD
continues to draw the minimum specified current. A dis-
connect timer counts up whenever port current is below
7.5mA (typ), indicating that the PD has been disconnected.
If the tDIS timer expires, the port will be turned off and
the disconnect bit in the fault event register will be set.
If the current returns before the tDIS timer runs out, the
timer resets and will start counting from the beginning
if the undercurrent condition returns. As long as the PD
exceeds the minimum current level more often than tDIS,
it will stay powered.
Although not recommended, the DC disconnect feature can
be disabled by clearing the corresponding DC Disconnect
Enable bits. Note that this defeats the protection mecha-
nisms built into the IEEE spec, since a powered port will
stay powered after the PD is removed. If the still-powered
port is subsequently connected to a non-PoE data device,
the device may be damaged.
The LTC4266 does not include AC disconnect circuitry, but
includes AC disconnect enable bits to maintain compat-
ibility with the LTC4259A. If the AC Disconnect Enable bits
are set, DC disconnect will be used.
Shutdown Pins
The LTC4266 includes a hardware SHDN pin for each port.
When a SHDN pin is pulled to DGND, the corresponding
port will be shut off immediately. The port remains shut
down until re-enabled via I2C or a device reset in AUTO
pin mode.
Masked Shutdown
The LTC4266 provides a low latency port shedding fea-
ture to quickly reduce the system load when required. By
allowing a pre-determined set of ports to be turned off,
the current on an overloaded main power supply can be
reduced rapidly while keeping high priority devices pow-
ered. Each port can be configured to high or low priority;
all low-priority ports will shut down within 6.5μs after
the MSD pin is pulled low. If multiple ports in a LTC4266
device are shut down via MSD, they are staggered by at
least 0.55μs to help reduce voltage transients on the main
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4267IDHC#TRPBF | IC POE 802.3AF INTERFACE 16-DFN |
| LTC4278IDKD#TRPBF | IC PD IEEE 802.3AT 25.5W 32-DFN |
| LTC4305IDHD#TRPBF | IC BUFFER BUS 2WR ADDRESS 16-DFN |
| LTC4306IUFD#TRPBF | IC MUX 4CH 2-WIRE BUS 24-QFN |
| LTC4310IMS-2#TRPBF | IC I2C ISOLATR 400KHZ BUS 10MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4266IUHF#PBF | 制造商:Linear Technology 功能描述:POE Controller 25.5W 38-Pin QFN EP 制造商:Linear Technology 功能描述:IC POE 802.3AT QUAD PSE 38-QFN 制造商:Linear Technology 功能描述:POE CNTRL QUAD 25.5W 1MHZ 制造商:Linear Technology 功能描述:IC, POE CONTROLLER, 3.3V, QFN-38; Input Voltage:3.3V; Supply Current:-2.4mA; UVLO:25V; Digital IC Case Style:QFN; No. of Pins:38; Frequency:1MHz; Operating Temperature Min:-40C; Operating Temperature Max:85C; MSL:MSL 1 - Unlimited ;RoHS Compliant: Yes |
| LTC4266IUHF#TRPBF | 制造商:Linear Technology 功能描述:POE Controller 25.5W 38-Pin QFN EP |
| LTC4267 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad IEEE 802.3at Power over Ethernet Controller |
| LTC4267-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
| LTC4267-3 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Power over Ethernet IEEE 802.3af PD Interface with Integrated Switching Regulator |
发布紧急采购，3分钟左右您将得到回复。