参数资料
型号: LTC4267IGN#PBF
厂商: Linear Technology
文件页数: 7/32页
文件大小: 0K
描述: IC POE 802.3AF INTERFACE 16SSOP
产品培训模块: Power over Ethernet
标准包装: 100
控制器类型: 以太网供电控制器(POE)
接口: IEEE 802.3af
电流 - 电源: 3mA
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 16-SSOP(0.154",3.90mm 宽)
供应商设备封装: 16-SSOP
包装: 管件
产品目录页面: 1338 (CN2011-ZH PDF)
相关产品: 732-2437-6-ND - TRANS FLYBACK POE 40UH SMD
732-2436-6-ND - TRANS FLYBACK POE 35UH SMD
732-2435-6-ND - TRANS FLYBACK POE 127UH SMD
732-2434-6-ND - TRANS FLYBACK POE 127UH SMD
732-2433-6-ND - TRANS FLYBACK POE 127UH SMD
732-2432-6-ND - TRANS FLYBACK POE 127UH SMD
732-2431-6-ND - TRANS FLYBACK POE 127UH SMD
732-2430-6-ND - TRANS FLYBACK POE 127UH SMD
732-2437-1-ND - TRANS FLYBACK POE 40UH SMD
732-2436-1-ND - TRANS FLYBACK POE 35UH SMD
更多...
LTC4267
15
4267fc
temperature exceeds the overtemperature trip point, the
current is reduced to zero and very little power is dissi-
pated in the part until it cools below the overtemperature
set point. Once the LTC4267 has charged up the load
capacitor and the PD is powered and running, there will
be minor residual heating due to the DC load current of
the PD owing through the internal MOSFET. The DHC
package offers superior thermal performance by including
an exposed pad that is soldered to an electrically isolated
heat sink on the printed circuit board.
During classication, excessive heating of the LTC4267
can occur if the PSE violates the 75ms probing time limit.
To protect the LTC4267, thermal overload circuitry will dis-
able classication current if the die temperature exceeds
the overtemperature trip point. When the die cools down
below the trip point, classication current is reenabled.
The PD is designed to operate at a high ambient tem-
perature and with the maximum allowable supply (57V).
However, there is a limit to the size of the load capacitor
that can be charged up before the LTC4267 reaches the
overtemperature trip point. Hitting the overtemperature
trip point intermittently does not harm the LTC4267, but it
will delay the completion of capacitor charging. Capacitors
up to 200F can be charged without a problem over the
full operating temperature range.
Switching Regulator Main Control Loop
Due to space limitations, the basics of current mode
DC/DC conversion will not be discussed here. The reader
is referred to the detail treatment in Application Note 19
or in texts such as Abraham Pressman’s Switching Power
Supply Design.
In a Power over Ethernet System, the majority of ap-
plications involve an isolated power supply design. This
means that the output power supply does not have any
DC electrical path to the PD interface or the switching
regulator primary. The DC isolation is achieved typically
through a transformer in the forward path and an op-
toisolator in the feedback path or a third winding in the
transformer. The typical application circuit shown on the
front page of the datasheet represents an isolated design
using an optoisolator. In applications where a nonisolated
topology is desired, the LTC4267 features a feedback port
and an internal error amplier that can be enabled for this
specic application.
In the typical application circuit (Figure 11), the isolated
topology employs an external resistive voltage divider
to present a fraction of the output voltage to an external
error amplier. The error amplier responds by pulling
an analog current through the input LED on an optoiso-
lator. The collector of the optoisolator output presents a
corresponding current into the ITH/RUN pin via a series
diode. This method generates a feedback voltage on the
ITH/RUN pin while maintaining isolation.
The voltage on the ITH/RUN pin controls the pulse-width
modulator formed by the oscillator, current comparator,
and RS latch. Specically, the voltage at the ITH/RUN pin
sets the current comparator’s trip threshold. The current
comparator monitors the voltage across a sense resistor
in series with the source terminal of the external N-Chan-
nel MOSFET. The LTC4267 turns on the external power
MOSFET when the internal free-running 200kHz oscillator
sets the RS latch. It turns off the MOSFET when the cur-
rent comparator resets the latch or when 80% duty cycle
is reached, whichever happens rst. In this way, the peak
current levels through the yback transformer’s primary
and secondary are controlled by the ITH/RUN voltage.
In applications where a nonisolated topology is desirable
(Figure 11), an external resistive voltage divider can present
a fraction of the output voltage directly to the VFB pin of
the LTC4267. The divider must be designed so when the
output is at its desired voltage, the VFB pin voltage will
equal the 800mV onboard internal reference. The internal
error amplier responds by driving the ITH/RUN pin. The
LTC4267 switching regulator performs in a similar manner
as described previously.
Regulator Start-Up/Shutdown
The LTC4267 switching regulator has two shutdown
mechanisms to enable and disable operation: an un-
dervoltage lockout on the PVCC supply pin and a forced
shutdown whenever external circuitry drives the ITH/RUN
pin low. The LTC4267 switcher transitions into and out of
shutdown according to the state diagram (Figure 8). It is
important not to confuse the undervoltage lockout of the
PD interface at VPORTN with that of the switching regulator
at PVCC. They are independent functions.
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料
PDF描述
PIC12C508AT-04E/SN IC MCU OTP 512X12 8SOIC
LTC1955EUH#PBF IC INTERFACE DL SMART CARD 32QFN
PIC16LF1512-E/SP IC MCU 8BIT 3.5KB FLASH 28-SPDIP
PIC16F1512-E/SP IC MCU 8BIT 3.5KB FLASH 28-SPDIP
PIC16F1827T-I/SS MCU PIC 8BIT 4K FLASH 20-SSOP
相关代理商/技术参数
参数描述
LTC4268-1 制造商:LINER 制造商全称:Linear Technology 功能描述:Quad IEEE 802.3at Power over Ethernet Controller
LTC4268-1_12 制造商:LINER 制造商全称:Linear Technology 功能描述:High Power PD With Synchronous No-Opto Flyback Controller
LTC4268CDKD-1 制造商:LINER 制造商全称:Linear Technology 功能描述:High Power PD with Synchronous NoOpto Flyback Controller
LTC4268CDKD-1#PBF 功能描述:IC PD HIGH POWER W/CNTRL 32-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统,AdvancedTCA ? 系统,高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-MSOP 包装:管件
LTC4268CDKD-1#TRPBF 功能描述:IC PD HIGH POWER W/CNTRL 32-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统,AdvancedTCA ? 系统,高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP,10-MSOP(0.118",3.00mm 宽) 供应商设备封装:10-MSOP 包装:管件