- 您现在的位置：买卖IC网 > PDF目录69007 > LTC4269CDKD-2#TR (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 PDF资料下载
参数资料
| 型号： | LTC4269CDKD-2#TR |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| 封装： | 7 X 4 MM, PLASTIC, M0-229, DFN-32 |
| 文件页数： | 2/34页 |
| 文件大小： | 383K |
| 代理商： | LTC4269CDKD-2#TR |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
LTC4269-2
0
42692fb
pin FuncTions
SHDN (Pin 1): Shutdown Input. Use this pin for auxiliary
power application. Drive SHDN high to disable LTC4269-2
operation and corrupt the signature resistance. If unused,
tie SHDN to VPORTN.
T2P (Pin 2): Type-2 PSE Indicator, Open-Drain. Low
impedance indicates the presence of a Type-2 PSE.
RCLASS (Pin 3): Class Select Input. Connect a resistor
between RCLASS and VPORTN to set the classification load
current.
VPORTN(Pins5,6):PowerInput.TietothePDinputthrough
the diode bridge. Pins 5 and 6 must be electrically tied
together at the package.
NC (Pins 4, 7, 8, 25, 30, 31): No Connect.
COMP (Pin 9): Output Pin of the Error Amplifier. The error
amplifier is an op amp, allowing various compensation
networks to be connected between the COMP pin and
FB pin for optimum transient response in a nonisolated
supply. The voltage on this pin corresponds to the peak
current of the external FET. Full operating voltage range is
between 0.8V and 2.5V corresponding to 0mV to 220mV
at the ISENSE pin. For applications using the 100mV OC
pin for overcurrent detection, typical operating range for
the COMP pin is 0.8V to 1.6V. For isolated applications
where COMP is controlled by an opto-coupler, the COMP
pin output drive can be disabled with FB = VREF, reducing
the COMP pin current to (COMP – 0.7)/40k.
FB(Pin10):Inanonisolatedsupply,FBmonitorstheoutput
voltage via an external resistor divider and is compared
with an internal 1.23V reference by the error amplifier. FB
connected to VREF disables error amplifier output.
ROSC (Pin11): A resistor to GND programs the operating
frequency of the IC between 100kHz and 500kHz. Nominal
voltage on the ROSC pin is 1.0V.
SYNC (Pin 12): Used to synchronize the internal oscillator
to an external signal. It is directly logic compatible and
can be driven with any signal between 10% and 90% duty
cycle. If unused, the pin should be connected to GND.
SS_MAXDC (Pin 13): The external resistor divider from
VREF sets the maximum duty cycle clamp (SS_MAXDC =
1.84V, SD_VSEC = 1.32V gives 72% duty cycle). Capacitor
on SS_MAXDC pin in combination with external resistor
divider sets soft-start timing.
VREF (Pin 14): The output of an internal 2.5V reference
which supplies internal control circuitry. Capable of sourc-
ing up to 2.5mA drive for external use. Bypass to GND
with a 0.1F ceramic capacitor.
SD_VSEC (Pin 15): The SD_VSEC pin, when pulled below
its accurate 1.32V threshold, is used to turn off the IC and
reduce current drain from VIN. The SD_VSEC pin is con-
nectedtosysteminputvoltagethrougharesistordividerto
define undervoltage lockout (UVLO) for the power supply
and to provide a volt-second clamp on the OUT pin. An
11A pin current hysteresis allows external programming
of UVLO hysteresis.
GND (Pin 16): Analog Ground. Tie to VNEG.
BLANK (Pin 17): A resistor to GND adjusts the extended
blanking period of the overcurrent and current sense
amplifier outputs during FET turn-on—to prevent false
current limit trip. Increasing the resistor value increases
the blanking period.
ISENSE (Pin 18): The Current Sense Input for the Control
Loop. Connect this pin to the sense resistor in the source
of the external power MOSFET. A resistor in series with
the ISENSE pin programs slope compensation.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4269IDKD-2 | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| LTC4269CDKD-2 | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| LTC4269IDKD-2#TR | SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDSO32 |
| LTC4412IS6#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| LTC4412IS6#TRM | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4269CDKD-2-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:IEEE 802.3at High Power PD and Synchronous Forward Controller with AUX Support |
| LTC4269IDKD-1#PBF | 功能描述:IC PD/OPTO FLYBACK CTRLR 32-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4269IDKD-1#TRPBF | 功能描述:IC PD/OPTO FLYBACK CTRLR 32-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| LTC4269IDKD-1-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller |
| LTC4269IDKD-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller |
发布紧急采购，3分钟左右您将得到回复。