- 您现在的位置：买卖IC网 > PDF目录44997 > LTC4280IUFD (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 PDF资料下载
参数资料
| 型号： | LTC4280IUFD |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC24 |
| 封装： | 4 X 5 MM, PLASTIC, MO-220, QFN-24 |
| 文件页数： | 4/28页 |
| 文件大小： | 286K |
| 代理商： | LTC4280IUFD |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC4280
12
4280f
The LTC4280 is designed to turn a board’s supply voltage
on and off in a controlled manner, allowing the board to be
safely inserted or removed from a live backplane. During
normal operation, the charge pump and gate driver turn
on an external N-channel MOSFET’s gate to pass power to
the load. The gate driver uses a charge pump that derives
its power from the VDD pin. Also included in the gate driver
is an internal 6.5V gate-to-source clamp. During start-up
the inrush current is tightly controlled by using current
limit foldback and output dV/dt limiting.
The current sense (CS) amplier monitors the load
current using the difference between the SENSE+ and
SENSE– pin voltages. The CS amplier limits the current
in the load by pulling back on the gate-to-source voltage
in an active control loop when the sense voltage exceeds
the commanded value. The CS amplier requires 20μA
input bias current from both the SENSE+ and the
SENSE– pins.
A short-circuit on the output to ground results in exces-
sive power dissipation during active current limiting. To
limit this power, the CS amplier regulates the voltage
between the SENSE+ and SENSE– pins at 26mV with
foldback to 10mV.
If an overcurrent condition persists, the internal circuit
breaker (CB) registers a fault when either the sense
voltage exceeds 25mV or the current sense amplier
is in regulation for more than the time limit set by the
capacitor on the FILTER pin. This indicates to the logic
that it is time to turn off the GATE to prevent overheating.
At this point the start-up TIMER pin voltage ramps down
using the 2μA current source until the voltage drops below
0.2V (comparator TM1) which tells the logic that the pass
transistor has cooled and it is safe to turn it on again if
overcurrent auto-retry is enabled. If the TIMER pin is tied
to INTVCC, the cool-down time defaults to 5 seconds on
an internal system timer in the logic.
The output voltage is monitored using the FB pin and the
Power Good (PG) comparator to determine if the power
is available for the load. The power good condition can be
signaled by the GPIO pin using an open-drain pulldown
transistor. The GPIO pin may also be congured to signal
power bad, or as a general purpose input (GP comparator),
or a general purpose open drain output.
The Functional Diagram shows the monitoring blocks of
the LTC4280. The group of comparators on the left side
includes the undervoltage (UV), overvoltage (OV), reset
(RST), enable (EN) and signal on (ON) comparators. These
comparators determine if the external conditions are valid
prior to turning on the GATE. But rst the two undervoltage
lockout circuits, UVLO1 and UVLO2, validate the input
supply and the internally generated 3.1V supply, INTVCC.
UVLO2 also generates the power-up initialization to the
logic circuits as INTVCC crosses this rising threshold. If the
xed internal overvoltage comparator, OV2, detects that
VDD is greater than 15.6V, the part immediately generates
an overvoltage fault and turns the GATE off.
Included in the LTC4280 is an 8-bit A/D converter. The
converter has a 3-input multiplexer to select between the
ADIN pin, the SOURCE pin and the SENSE+ – SENSE–
voltage.
An I2C interface is provided to read the A/D registers. It
also allows the host to poll the device and determine if
faults have occurred. If the ALERT line is congured as an
interrupt, the host is enabled to respond to faults in real
time. The typical SDA line is divided into an SDAI (input)
and SDAO (output). This simplies applications using an
optoisolator driven directly from the SDAO output. An
application which uses optoisolation is shown on the back
cover. The I2C device address is decoded using the ADR0,
ADR1 and ADR2 pins. These inputs have three states each
that decode into a total of 27 device addresses.
OPERATION
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4312IDE#TRPBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| LTC4312CDE#PBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO14 |
| LTC4312IMS#TRPBF | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4352CMS#PBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO12 |
| LTC4352CDD#TRPBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO12 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4280IUFD#PBF | 功能描述:IC HOT SWAP CONTROLLER 24-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4280IUFD#TRPBF | 功能描述:IC CTLR HOT SWAP I2C MON 24QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:119 系列:- 类型:热交换控制器 应用:通用型，PCI Express? 内部开关:无 电流限制:- 电源电压:3.3V，12V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:80-TQFP 供应商设备封装:80-TQFP（12x12） 包装:托盘 产品目录页面:1423 (CN2011-ZH PDF) |
| LTC4280IUFD-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280IUFD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
发布紧急采购，3分钟左右您将得到回复。