- 您现在的位置：买卖IC网 > PDF目录11806 > LTC4305CGN#PBF (Linear Technology)IC BUFFER BUS 2WR ADDRESS 16SSOP PDF资料下载
参数资料
| 型号： | LTC4305CGN#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC BUFFER BUS 2WR ADDRESS 16SSOP |
| 产品培训模块： | LTC4310 - Hot-Swappable I²C Isolators |
| 标准包装： | 100 |
| 应用： | 带放大器的多路复用器 |
| 接口： | SMBus（2 线/I²C） |
| 电源电压： | 2.2 V ~ 5.5 V |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1355 (CN2011-ZH PDF) |
LTC4305
15
4305f
Design Example
A typical LTC4305 application circuit is shown in Figure 5.
The circuit illustrates the level-shifting, multiplexer/switch
and capacitance buffering features of the LTC4305. In this
application, the LTC4305 VCC voltage and downstream
bus 1 are powered from 3.3V, downstream bus 2 is
powered from 5V, and the upstream bus is powered from
2.5V. The following sections describe a methodology for
choosing the external components in Figure 5.
SDA, SCL Pull-Up Resistor Selection
The pull-up resistors on the SDA and SCL pins must be
strong enough to provide a minimum of 100
A pull-up
current, per the SMBus Specification. In most systems,
the required minimum strength of the pull-up resistors is
determined by the minimum slew requirement to guaran-
tee that the LTC4305’s rise time accelerators are activated
during rising edges. At the same time, the pull-up value
should be kept low to maximize the logic low noise margin
and minimize the offset voltage of the Upstream-Down-
stream Buffer circuitry. The LTC4305 is designed to
function for a maximum DC pull-up current of 4mA. If
multiple downstream channels are active at the same time,
this means that the sum total of the pull-up currents from
these channels must be less than 4mA. At supply voltages
of 2.7V and 5.5V, pull-up resistor values of 10k work well
for capacitive loads up to 215pF and 420pF, respectively.
For larger bus capacitances, refer to equation (1) below.
The LTC4305 works with capacitive loads up to 2nF.
Assume in Figure 5 that the total parasitic bus capacitance
on SDA1 due to trace and device capacitance is 100pF. To
ensure that the boost currents are active during rising
edges, the pull-up resistor must be strong enough to
cause the SDA1 pin voltage to rise at a rate of 0.8V/
s as
the pin voltage is rising above 0.8V. The equation is:
Rk
VV
ns
V
PULL UP MAX
BUSMIN
[]=
,
(– .
)
0 8
1250
[]
CpF
BUS
(1)
where VBUSMIN is the minimum operating pull-up supply
voltage, and CBUS is the bus parasitic capacitance. In our
example, VBUS1 = VCC = 3.3V, and assuming ±10% supply
tolerance, VBUS1MIN = 2.97V. With CBUS = 100pF,
RPULL-UP,MAX = 27.1k. Therefore, we must choose a
pull-up resistor smaller (i.e., stronger pull-up) than 27.1k,
so a 10k resistor works fine.
ALERT and READY Component Selection
The pull-up resistors on the ALERT and READY pins must
provide a maximum pull-up current of 3mA, so that the
LTC4305 is capable of holding the pins at logic low
voltages below 0.4V.
APPLICATIO S I FOR ATIO
WU
U
Figure 5. A Level Shifting Circuit
4305 F05
4
8
9
10
2
3
5
1
15
16
14
13
12
7
R4
10k
C1
0.01
F
R5
10k
R6
10k
R2
10k
R3
10k
R1
10k
ADDRESS = 1000 100
SFP
MODULE #1
R7
10k
R8
10k
R9
10k
ADDRESS = 1111 000
MICRO-
CONTROLLER
SFP
MODULE #2
ADDRESS = 1111 001
VBACK = 2.5V
VBUS2 = 5V
VCC = VBUS1 = 3.3V
SCLIN
SDAIN
ALERT
ADR2
ADR1
ADR0
GND
SCL1
SDA1
ALERT1
SCL2
SDA2
ALERT2
VCC
LTC4305
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1755EGN#PBF | IC SMART CARD INTERFACE 24SSOP |
| AT32UC3C264C-A2UR | IC MCU AVR32 64K FLASH 64TQFP |
| LTC1756EGN#PBF | IC SMART CARD INTERFACE 16SSOP |
| AT89C51IC2-RLRUL | IC 8051 MCU 32K FLASH 44-VQFP |
| ATMEGA645V-8AUR | MCU AVR 64KB FLASH 8MHZ 64TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4305IDHD | 功能描述:IC BUFFER BUS 2WR ADDRESS 16-DFN RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC4305IDHD#PBF | 功能描述:IC BUFFER BUS 2WR ADDRESS 16-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC4305IDHD#TR | 功能描述:IC BUFFER BUS 2WR ADDRESS 16-DFN RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC4305IDHD#TRPBF | 功能描述:IC BUFFER BUS 2WR ADDRESS 16-DFN RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| LTC4305IGN | 功能描述:IC BUFFER BUS 2WR ADDRESS 16SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
发布紧急采购，3分钟左右您将得到回复。