参数资料
| 型号： | LTC4313IMS8-1#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/20页 |
| 文件大小： | 0K |
| 描述： | IC 2WIRE BUS BUFFER 8MSOP |
| 标准包装： | 50 |
| 类型： | 2线总线缓冲器 |
| Tx/Rx类型： | I²C Logic |
| 电容 - 输入： | 10pF |
| 电源电压： | 2.9 V ~ 5.5 V |
| 电流 - 电源： | 8.1mA |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
LTC4313-1/LTC4313-2/
LTC4313-3
7
4313123f
operaTion
The LTC4313 is a high noise margin bus buffer which
providescapacitancebufferingforI2Csignals.Capacitance
buffering is achieved by using back to back buffers on
the clock and data channels which isolate the SDAIN
and SCLIN capacitances from the SDAOUT and SCLOUT
capacitances respectively. All SDA and SCL pins are fully
bidirectional. The high noise margin allows the LTC4313 to
operate with non-compliant I2C devices that drive a high
VOL, permits a number of LTC4313s to be connected in
series and improves the reliability of I2C communications
inlargenoisysystems.Risetimeaccelerator(RTA)pull-up
currents (IRTA) turn on during rising edges to reduce bus
rise time for the LTC4313-1 and LTC4313-2. In a typical
application the input and output busses are pulled up to
VCC although this is not a requirement. If VDD,BUS is not
tied to VCC, VDD,BUS must be greater than VCC to prevent
overdrive of the bus by the RTAs for the LTC4313-1 and
LTC4313-2. See the Applications Information section for
VDD,BUS requirements for the LTC4313-3.
When the LTC4313 first receives power on its VCC pin, it
starts out in an undervoltage lockout mode (UVLO) until
its VCC exceeds 2.7V. The buffers and RTAs are disabled
and the LTC4313 ignores the logic state of its clock and
data pins. During this time the precharge circuit forces a
nominal voltage of 1V on the SDA and SCL pins through
200k resistors.
Once the LTC4313 exits UVLO and its ENABLE pin has
been asserted high, it monitors the clock and data pins
for a stop bit or a bus idle condition. When a combination
of either condition is detected simultaneously on the input
and output sides, the LTC4313 activates the connection
between SDAIN and SDAOUT, and SCLIN and SCLOUT,
respectively, asserts READY high and deactivates the
precharge circuit. RTAs for the LTC4313-1 and LTC4313-2
are also enabled at this time.
When a SDA/SCL pin is driven below the VIL level, the
buffers are turned on and the logic low level is propagated
though the LTC4313 to the other side. A high occurs when
alldevicesontheinputandoutputsidesreleasehigh.Once
the bus voltages rise above the VIL level, the buffers are
turned off. The RTAs are turned on at a slightly higher volt-
age. The RTAs accelerate the rising edges of the SDA/SCL
inputs and outputs up to a voltage of 0.9VCC, provided
that the busses on their own are rising at a minimum rate
of 0.4V/s as determined by the slew rate detectors. The
RTAs are configured to operate in a strong slew limited
switch mode in the LTC4313-1 and in the current source
mode in the LTC4313-2.
The LTC4313 detects a bus stuck low (fault) condition
when both clock and data busses are not simultaneously
high at least once in 45ms. When a stuck bus occurs, the
LTC4313 disconnects the input and output sides and after
waiting at least 40s, generates up to sixteen 5.5kHz clock
pulses on the SCLOUT pin and a stop bit to attempt to free
the stuck bus. Should the stuck bus release high during
this period, automatic clock generation is terminated.
Once the stuck bus recovers, connection is re-established
between the input and output after a stop bit or bus idle
condition is detected. Toggling ENABLE after a fault condi-
tion has occurred forces a connection between the input
and output. When powering into a stuck low condition, the
input and output sides remain disconnected even after the
LTC4313 has exited the UVLO mode as a stop bit or bus
idle condition is not detected on the stuck busses. After
the timeout period, a stuck low fault condition is detected
and the behavior is as described previously.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4314IGN#PBF | IC MULTIPLEXER 20-MSOP |
| LTC4315IMS#TRPBF | IC 2WIRE BUS BUFFER 12MSOP |
| LTC485IS8#TRPBF | IC TXRX INTRFC RS485 LOPWR 8SOIC |
| LTC487IN#PBF | IC DVR RS485 LOW PWR QUAD 16-DIP |
| LTC488ISW#TRPBF | IC LINE RCVR RS485 QUAD 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4313IMS8-2#PBF | 功能描述:IC 2WIRE BUS BUFFER 8MSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号缓冲器，中继器，分配器 系列:- 标准包装:160 系列:- 类型:转发器 Tx/Rx类型:以太网 延迟时间:- 电容 - 输入:- 电源电压:2.37 V ~ 2.63 V 电流 - 电源:60mA 安装类型:表面贴装 封装/外壳:64-TQFP 裸露焊盘 供应商设备封装:64-TQFP-EP（10x10） 包装:托盘 其它名称:Q5134101 |
| LTC4313IMS8-2#TRPBF | 功能描述:IC 2WIRE BUS BUFFER 8MSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号缓冲器，中继器，分配器 系列:- 标准包装:160 系列:- 类型:转发器 Tx/Rx类型:以太网 延迟时间:- 电容 - 输入:- 电源电压:2.37 V ~ 2.63 V 电流 - 电源:60mA 安装类型:表面贴装 封装/外壳:64-TQFP 裸露焊盘 供应商设备封装:64-TQFP-EP（10x10） 包装:托盘 其它名称:Q5134101 |
| LTC4313IMS8-3#PBF | 功能描述:IC 2WIRE BUS BUFFER 8MSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号缓冲器，中继器，分配器 系列:- 标准包装:160 系列:- 类型:转发器 Tx/Rx类型:以太网 延迟时间:- 电容 - 输入:- 电源电压:2.37 V ~ 2.63 V 电流 - 电源:60mA 安装类型:表面贴装 封装/外壳:64-TQFP 裸露焊盘 供应商设备封装:64-TQFP-EP（10x10） 包装:托盘 其它名称:Q5134101 |
| LTC4313IMS8-3#TRPBF | 功能描述:IC 2WIRE BUS BUFFER 8MSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号缓冲器，中继器，分配器 系列:- 标准包装:160 系列:- 类型:转发器 Tx/Rx类型:以太网 延迟时间:- 电容 - 输入:- 电源电压:2.37 V ~ 2.63 V 电流 - 电源:60mA 安装类型:表面贴装 封装/外壳:64-TQFP 裸露焊盘 供应商设备封装:64-TQFP-EP（10x10） 包装:托盘 其它名称:Q5134101 |
| LTC4314CGN#PBF | 功能描述:IC MULTIPLEXER 20-MSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 信号缓冲器，中继器，分配器 系列:* 标准包装:160 系列:- 类型:转发器 Tx/Rx类型:以太网 延迟时间:- 电容 - 输入:- 电源电压:2.37 V ~ 2.63 V 电流 - 电源:60mA 安装类型:表面贴装 封装/外壳:64-TQFP 裸露焊盘 供应商设备封装:64-TQFP-EP（10x10） 包装:托盘 其它名称:Q5134101 |
发布紧急采购，3分钟左右您将得到回复。