- 您现在的位置：买卖IC网 > PDF目录20350 > LTC4412ES6#TR (Linear Technology)IC CTRLR LOWLOS PWRPATH TSOT23-6 PDF资料下载
参数资料
| 型号： | LTC4412ES6#TR |
| 厂商： | Linear Technology |
| 文件页数： | 6/12页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR LOWLOS PWRPATH TSOT23-6 |
| 标准包装： | 2,500 |
| 系列： | PowerPath™ |
| 应用： | 手持/移动设备 |
| FET 型： | P 沟道 |
| 输出数： | 1 |
| 内部开关： | 无 |
| 延迟时间 - 开启： | 110µs |
| 延迟时间 - 关闭： | 13µs |
| 电源电压： | 2.5 V ~ 28 V |
| 电流 - 电源： | 16µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 供应商设备封装： | TSOT-23-6 |
| 包装： | 带卷 (TR) |
| 其它名称： | LTC4412ES6TR |
LTC4412
OPERATIO
Operation can best be understood by referring to the Block
Diagram, which illustrates the internal circuit blocks along
with the few external components, and the graph that
accompanies Figure 1. The terms primary and auxiliary are
arbitrary and may be changed to suit the application.
Operation begins when either or both power sources are
applied and the CTL control pin is below the input low
voltage of 0.35V (V IL ). If only the primary supply is
present, the Power Source Selector will power the LTC4412
from the V IN pin. Amplifier A1 will deliver a current to the
Analog Controller block that is proportional to the voltage
difference in the V IN and SENSE pins. While the voltage on
SENSE is lower than V IN – 20mV (V FR ), the Analog
Controller will instruct the Linear Gate Driver and Voltage
Clamp block to pull down the GATE pin voltage and turn on
the external P-channel MOSFET. The dynamic pull-down
current of 50 μ A (I G(SNK) ) stops when the GATE voltage
reaches ground or the gate clamp voltage. The gate clamp
voltage is 7V (V G(ON) ) below the higher of V IN or V SENSE .
As the SENSE voltage pulls up to V IN – 20mV, the LTC4412
will regulate the GATE voltage to maintain a 20mV differ-
ence between V IN and V SENSE which is also the V DS of the
MOSFET. The system is now in the forward regulation
mode and the load will be powered from the primary
supply. As the load current varies, the GATE voltage will be
controlled to maintain the 20mV difference. If the load
current exceeds the P-channel MOSFET’s ability to deliver
the current with a 20mV V DS the GATE voltage will clamp,
the MOSFET will behave as a fixed resistor and the forward
voltage will increase slightly. While the MOSFET is on the
STAT pin is an open circuit.
When an auxiliary supply is applied, the SENSE pin will be
pulled higher than the V IN pin through the external diode.
The Power Source Selector will power the LTC4412 from
the SENSE pin. As the SENSE voltage pulls above V IN –
20mV, the Analog Controller will instruct the Linear Gate
Driver and Voltage Clamp block to pull the GATE voltage up
to turn off the P-channel MOSFET. When the voltage on
SENSE is higher than V IN + 20mV (V RTO ), the Analog
Controller will instruct the Linear Gate Driver and Voltage
Clamp block to rapidly pull the GATE pin voltage to the
SENSE pin voltage. This action will quickly finish turning
off the external P-channel MOSFET if it hasn’t already
turned completely off. For a clean transistion, the reverse
turn-off threshold has hysteresis to prevent uncertainty.
The system is now in the reverse turn-off mode. Power to
the load is being delivered through the external diode and
no current is drawn from the primary supply. The external
diode provides protection in case the auxiliary supply is
below the primary supply, sinks current to ground or is
connected reverse polarity. During the reverse turn-off
mode of operation the STAT pin will sink 10 μ A of current
(I S(SNK) ) if connected. Note that the external MOSFET is
wired so that the drain to source diode will momentarily
forward bias when power is first applied to V IN and will
become reverse biased when an auxiliary supply is ap-
plied.
When the CTL (control) input is asserted high, the external
MOSFET will have its gate to source voltage forced to a
small voltage V G(OFF) and the STAT pin will sink 10 μ A of
current if connected. This feature is useful to allow control
input switching of the load between two power sources as
shown in Figure 4 or as a switchable high side driver as
shown in Figure 7. A 3.5 μ A internal pull- down current
(I CTL ) on the CTL pin will insure a low level input if the pin
should become open.
4412fa
6
相关PDF资料 |
PDF描述 |
|---|---|
| EEM24DRTS | CONN EDGECARD 48POS DIP .156 SLD |
| VI-B64-CX-F1 | CONVERTER MOD DC/DC 48V 75W |
| VI-B64-CW-F4 | CONVERTER MOD DC/DC 48V 100W |
| MAX1614EUA | IC DRIVER SW MOSF HI SIDE 8UMAX |
| F750J108KRC | CAP TANT 1000UF 6.3V 10% 2824 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4412ES6TRMPBF | 制造商:Linear Technology 功能描述:Automatic Pwr Path Controller LTC4412ES6 |
| LTC4412HVIS6 | 制造商:Linear Technology 功能描述:Power Controller 6-Pin TSOT-23 |
| LTC4412HVIS6#PBF | 制造商:Linear Technology 功能描述:IDEAL DIODE CNTRL 36V 6TSOT2 制造商:Linear Technology 功能描述:IDEAL DIODE CNTRL, 36V, 6TSOT23 |
| LTC4412HVIS6#TR | 功能描述:IC CONTROLLER LOW LOSS TSOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4412HVIS6#TRM | 功能描述:IC CONTROLLER LOW LOSS TSOT23-6 RoHS:否 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。