参数资料
| 型号： | LTC4416EMS#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 3/12页 |
| 文件大小： | 0K |
| 描述： | IC CTLR POWERPATH 10-MSOP |
| 标准包装： | 50 |
| 系列： | PowerPath™ |
| 应用： | 电池备份，工业/汽车，大电流开关 |
| FET 型： | P 沟道 |
| 输出数： | 2 |
| 内部开关： | 无 |
| 延迟时间 - 开启： | 60µs |
| 延迟时间 - 关闭： | 30µs |
| 电源电压： | 3.6 V ~ 36 V |
| 电流 - 电源： | 130µA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 管件 |
| 产品目录页面： | 1338 (CN2011-ZH PDF) |
LTC4416/LTC4416-1
ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T A = 25°C. V1 = V2 = 12V, E1 = 2V, E2 = GND, GND = 0V. Current into a pin is
positive an d current out of a pin is negative. All voltages are referenced to GND, unless otherwise specified .
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
G1, G2 Controller
I G(SRC)
I G(SNK)
I G(FO)
I G(OFF)
V G(ON)
V G(OFF)
t G(ON)
t G(OFF)
t E(OFF)
GATE Active Forward Regulation
Source Current
Sink Current
Sink Current During Fast-On
Source Current During Fast-Off
G1 and G2 Clamp Voltage
G1 and G2 Off Voltage
G1 and G2 Turn-On Time
G1 and G2 Turn-Off Time
Enable Comparator Turn-Off Delay
(Note 5)
(Note 6)
(Note 7)
(Note 12)
Apply I G1 = I G2 = 2μA, V V1 = V V2 = 12V,
V VS = 11.8V, Measure V V1 – V G1 or V V2 – V G2
Apply I G1 = I G2 = –30μA, V V1 = V V2 = 12V,
V VS = 12.2V, Measure V V1 – V G1 or V V2 – V G2
V GS < –6V, C G = 17nF (Note 8)
V GS > –1.5V, C G = 17nF (Note 9)
(Note 14) LTC4416-1 Only
●
●
●
●
●
–9
15
500
7.4
8.25
0.350
–2
200
–500
9.1
0.920
60
30
6
μA
μA
μA
μA
V
V
μs
μs
μs
H1 and H2 Open-Drain Drivers
I H(OFF)
V H(ON)
t H(ON)
t H(OFF)
H1 and H2 Off Current
H1 and H2 On Voltage
H1 and H2 Turn-On Time
H1 and H2 Turn-Off Time
3.6V ≤ V V1 , V V2 ≤ 36V (Note 10)
3.6V ≤ V V1 , V V2 ≤ 36V (Note 10)
(Note 11)
(Note 11)
●
●
–1
1
100
5
10
μA
mV
μs
μs
E1 and E2 Enable Input Comparators
V REF
I E
E1 and E2 Input Threshold Voltage
E1 and E2 Input Leakage Current
3.6V ≤ V V1 , V V2 ≤ 36V, –40°C to 85°C
4V ≤ V V1 , V V2 ≤ 36V, –40°C to 125°C
0V ≤ V E1 , V E2 ≤ 1.5V
●
1.180
1.180
–100
1.215
1.215
1.240
1.240
100
V
V
nA
I G(ENOFF)
Source Current When Other Channel
Enabled (Note 13)
LTC4416
LTC4416-1
–9
–500
–3
μA
μA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LTC4416E is guaranteed to meet performance specifications
from 0°C to 85°C. Specifications over the –40°C to 85°C operating
temperature range are assured by design, characterization and correlation
with statistical process controls. The LTC4416I is guaranteed and tested
over the –40°C to 125°C operating temperature range.
Note 3: This results in the same supply current as would be observed with
an external P-channel MOSFET connected to the LTC4416 and operating in
forward regulation.
Note 4: Only 3 of 9 permutations illustrated. This specification is the same
when power is provided through V S or V2. This specification is only valid
when V1, V2 and V S are within 28V of each other.
Note 5: V1 and V2 are held at 12V and G1 and G2 are forced to 9V. V S is
set at 12V to measure the source current at either G1 or G2.
Note 6: V1 and V2 are held at 12V and G1 and G2 are forced to 9V. V S is
set at 11.96V to measure the sink current at either G1 or G2.
Note 8: V1 and V2 are held at 12V and V S is stepped from 12.2V to 11.8V
to trigger the event. G1 and G2 voltages are initially V G(OFF) .
Note 9: V1 and V2 are held at 12V and V S is stepped from 11.8V to 12.2V
to trigger the event. G1 and G2 voltages are initially V G(ON) .
Note 10: H1 and H2 are forced to 2 V. E1 and E2 are forced to 1.5V to
measure the off current of H1 and H2. H1 and H2 are forced with 1mA to
measure the on voltage of H1 and H2.
Note 11: H1 and H2 are forced to 2V . E1 and E2 are stepped from 1.3V
to 1.1V to measure t S(ON) . E1 and E2 are stepped from 1.1V to 1.3V to
measure t S(OFF) .
Note 12: V1 and V2 are held at 12V and G1 and G2 are forced to 9V. V S is
set to 12.05V to measure the source current at either G1 or G2.
Note 13: V1 and V2 are held at 12V and G1 and G2 are forced to 9V. V S
is set to 12V to measure the source current at either G1 or G2 when the
channel is deselected.
Note 14: V1 and V2 are held at 12V, V S = 11.96V and G1 and G2 have a 4k
resistor each to 9V. Measure the delay after the channel is disabled until
the gate signal begins to pull high.
Note 7: V1 and V2 are held at 12V and G1 and G2 are forced to 9V. V S is
set at 11.875V to measure the sink current at either G1 or G2.
4416fa
相关PDF资料 |
PDF描述 |
|---|---|
| LTC5100EUF#TRPBF | IC DRIVER VCSEL 3.2GBPS 16QFN |
| LTC660CS8#TRPBF | IC REG DBL INV ADJ 0.1A 8SOIC |
| LTC6801HG#TRPBF | IC BATTERY MON MULTICELL 36SSOP |
| LTC6802IG-1#TRPBF | IC MONITOR BATT STACK MC 44-SSOP |
| LTC6803HG-1#TRPBF | IC MONITOR BATT STACK 44-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4416IMS#PBF | 功能描述:IC CNTRLR POWERPATH 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4416IMS#TRPBF | 功能描述:IC CNTRLR POWERPATH 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4416IMS-1 | 制造商:Linear Technology 功能描述:OR Controller P-Channel Dual-OUT 10-Pin MSOP |
| LTC4416IMS-1#PBF | 功能描述:IC CNTRLR POWERPATH 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
| LTC4416IMS-1#TRPBF | 功能描述:IC CNTRLR POWERPATH 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - O 圈控制器 系列:PowerPath™ 标准包装:1,000 系列:- 应用:电池备份，工业/汽车，大电流开关 FET 型:- 输出数:5 内部开关:是 延迟时间 - 开启:100ns 延迟时间 - 关闭:- 电源电压:3 V ~ 5.5 V 电流 - 电源:250µA 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 供应商设备封装:16-SOIC N 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。