参数资料
型号: LTC486CN
厂商: Linear Technology
文件页数: 14/14页
文件大小: 0K
描述: IC DVR RS485 LOW PWR QUAD 16-DIP
标准包装: 25
类型: 驱动器
驱动器/接收器数: 4/0
规程: RS422,RS485
电源电压: 4.75 V ~ 5.25 V
安装类型: 通孔
封装/外壳: 16-DIP(0.300",7.62mm)
供应商设备封装: 16-PDIP
包装: 管件
LTC486
9
486fc
APPLICATIONS INFORMATION
When using low loss cables, Figure 8 can be used as a
guidelineforchoosingthemaximumlinelengthforagiven
data rate. With lower quality PVC cables, the dielectric loss
factor can be 1000 times worse. PVC twisted pairs have
terrible losses at high data rates (>100kbs) and greatly
reduce the maximum cable length. At low data rates how-
ever, they are acceptable and much more economical.
Cable Termination
The proper termination of the cable is very important. If
the cable is not terminated with its characteristic imped-
ance, distorted waveforms will result. In severe cases,
distorted (false) data and nulls will occur. A quick look
at the output of the driver will tell how well the cable is
terminated. It is best to look at a driver connected to the
end of the cable, since this eliminates the possibility of
getting reflections from two directions. Simply look at the
driver output while transmitting square wave data. If the
cable is terminated properly, the waveform will look like
a square wave (Figure 9).
If the cable is loaded excessively (e.g., 47), the signal
initially sees the surge impedance of the cable and jumps
to an initial amplitude. The signal travels down the cable
and is reflected back out of phase because of the mister-
mination. When the reflected signal returns to the driver,
the amplitude will be lowered. The width of the pedestal
is equal to twice the electrical length of the cable (about
1.5ns/ft). If the cable is lightly loaded (e.g., 470), the
signal reflects in phase and increases the amplitude at the
driver output. An input frequency of 30kHz is adequate for
tests out to 4000 ft. of cable.
AC Cable Termination
Cable termination resistors are necessary to prevent un-
wanted reflections, but they consume power. The typical
differential output voltage of the driver is 2V when the
cable is terminated with two 120 resistors. When no
data is being sent 33mA of DC current flows in the cable.
This DC current is about 220 times greater than the supply
current of the LTC486. One way to eliminate the unwanted
current is by AC coupling the termination resistors as
shown in Figure 10.
Figure 8. Cable Length vs Data Rate
DATA RATE (bps)
10k
10
CABLE
LENGTH
(FT)
100
1k
10k
100k
1M
10M
486 F08
2.5M
Figure 9. Termination Effects
Rt
DRIVER
DX
RECEIVER
RX
Rt = 120
Rt = 47
Rt = 470
486 F09
PROBE HERE
486 F10
C = LINE LENGTH (FT)
× 16.3pF
120
RECEIVER
RX
C
Figure 10. AC Coupled Termination
相关PDF资料
PDF描述
MS27466E11F5S CONN RCPT 5POS WALL MT W/SCKT
MS3100E16-10PW CONN RCPT 3POS WALL MNT W/PINS
LTC1383IN#PBF IC TXRX 5V RS232 LOW PWR 16-DIP
LTC1742CFW#PBF IC ADC 14BIT 65MSPS 48-TSSOP
LT1039ISW#PBF IC DRIVR/RCVR TRPLE-RS232 18SOIC
相关代理商/技术参数
参数描述
LTC486CN#PBF 功能描述:IC DVR RS485 LOW PWR QUAD 16-DIP RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 产品培训模块:RS-232 & USB Transceiver 标准包装:2,000 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SSOP(0.209",5.30mm 宽) 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:296-19849-2
LTC486CNPBF 制造商:Linear Technology 功能描述:LTC486CNPBF
LTC486CSW 功能描述:IC DVR RS485 LOW PWR QUAD 16SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232,RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC 包装:管件
LTC486CSW#PBF 功能描述:IC DVR RS485 LOW PWR QUAD 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 产品培训模块:RS-232 & USB Transceiver 标准包装:2,000 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SSOP(0.209",5.30mm 宽) 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:296-19849-2
LTC486CSW#PBF 制造商:Linear Technology 功能描述:IC RS-485 BUS/LINE DRIVER 5V SOL-16