参数资料
型号: LTC486CSW
厂商: Linear Technology
文件页数: 14/14页
文件大小: 0K
描述: IC DVR RS485 LOW PWR QUAD 16SOIC
标准包装: 47
类型: 驱动器
驱动器/接收器数: 4/0
规程: RS422,RS485
电源电压: 4.75 V ~ 5.25 V
安装类型: 表面贴装
封装/外壳: 16-SOIC(0.295",7.50mm 宽)
供应商设备封装: 16-SOIC
包装: 管件
其它名称: LTC486CS
LTC486
9
486fc
APPLICATIONS INFORMATION
When using low loss cables, Figure 8 can be used as a
guidelineforchoosingthemaximumlinelengthforagiven
data rate. With lower quality PVC cables, the dielectric loss
factor can be 1000 times worse. PVC twisted pairs have
terrible losses at high data rates (>100kbs) and greatly
reduce the maximum cable length. At low data rates how-
ever, they are acceptable and much more economical.
Cable Termination
The proper termination of the cable is very important. If
the cable is not terminated with its characteristic imped-
ance, distorted waveforms will result. In severe cases,
distorted (false) data and nulls will occur. A quick look
at the output of the driver will tell how well the cable is
terminated. It is best to look at a driver connected to the
end of the cable, since this eliminates the possibility of
getting reflections from two directions. Simply look at the
driver output while transmitting square wave data. If the
cable is terminated properly, the waveform will look like
a square wave (Figure 9).
If the cable is loaded excessively (e.g., 47), the signal
initially sees the surge impedance of the cable and jumps
to an initial amplitude. The signal travels down the cable
and is reflected back out of phase because of the mister-
mination. When the reflected signal returns to the driver,
the amplitude will be lowered. The width of the pedestal
is equal to twice the electrical length of the cable (about
1.5ns/ft). If the cable is lightly loaded (e.g., 470), the
signal reflects in phase and increases the amplitude at the
driver output. An input frequency of 30kHz is adequate for
tests out to 4000 ft. of cable.
AC Cable Termination
Cable termination resistors are necessary to prevent un-
wanted reflections, but they consume power. The typical
differential output voltage of the driver is 2V when the
cable is terminated with two 120 resistors. When no
data is being sent 33mA of DC current flows in the cable.
This DC current is about 220 times greater than the supply
current of the LTC486. One way to eliminate the unwanted
current is by AC coupling the termination resistors as
shown in Figure 10.
Figure 8. Cable Length vs Data Rate
DATA RATE (bps)
10k
10
CABLE
LENGTH
(FT)
100
1k
10k
100k
1M
10M
486 F08
2.5M
Figure 9. Termination Effects
Rt
DRIVER
DX
RECEIVER
RX
Rt = 120
Rt = 47
Rt = 470
486 F09
PROBE HERE
486 F10
C = LINE LENGTH (FT)
× 16.3pF
120
RECEIVER
RX
C
Figure 10. AC Coupled Termination
相关PDF资料
PDF描述
IDT72231L25JI IC FIFO SYNC 512X9 25NS 32PLCC
LTC2221CUP#PBF IC ADC 12-BIT 135MSPS 64-QFN
MS27467E17A26SB CONN PLUG 26POS STRAIGHT W/SCKT
MS27473T24A61PD CONN PLUG 61POS STRAIGHT W/PINS
AD7872KRZ-REEL IC ADC 14BIT SAMPLING 16SOIC
相关代理商/技术参数
参数描述
LTC486CSW#PBF 功能描述:IC DVR RS485 LOW PWR QUAD 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 产品培训模块:RS-232 & USB Transceiver 标准包装:2,000 系列:- 类型:收发器 驱动器/接收器数:1/1 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SSOP(0.209",5.30mm 宽) 供应商设备封装:16-SSOP 包装:带卷 (TR) 其它名称:296-19849-2
LTC486CSW#PBF 制造商:Linear Technology 功能描述:IC RS-485 BUS/LINE DRIVER 5V SOL-16
LTC486CSW#TR 功能描述:IC DRIVER RS485 QUAD LP 16SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232,RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC 包装:管件
LTC486CSW#TRPBF 功能描述:IC DVR RS485 LOW PWR QUAD 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器,接收器,收发器 系列:- 标准包装:27 系列:- 类型:收发器 驱动器/接收器数:3/3 规程:RS232,RS485 电源电压:4.75 V ~ 5.25 V 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC 包装:管件
LTC486CSWPBF 制造商:Linear Technology 功能描述:LTC486CSWPBF