参数资料
| 型号： | LTC6102CDD#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 6/26页 |
| 文件大小： | 0K |
| 描述： | IC AMP CURRENT SENSE 8-DFN |
| 标准包装： | 2,500 |
| 放大器类型： | 电流检测 |
| 电路数： | 1 |
| 增益带宽积： | 200kHz |
| 电流 - 输入偏压： | 60pA |
| 电压 - 输入偏移： | 3µV |
| 电流 - 电源： | 420µA |
| 电流 - 输出 / 通道： | 1mA |
| 电压 - 电源，单路/双路(±)： | 4 V ~ 60 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-DFN-EP（3x3） |
| 包装： | 带卷 (TR) |
LTC6102
LTC6102-1/LTC6102HV
14
6102fd
the largest expected sense voltage gives IOUT = 1mA, then
the maximum output dynamic range is available. Output
dynamic range is limited by both the maximum allowed
output current (Note 1) and the maximum allowed output
voltage, as well as the minimum practical output signal. If
less dynamic range is required, then RIN can be increased
accordingly, reducing the output current and power dis-
sipation. If small sense currents must be resolved ac-
curately in a system that has very wide dynamic range, a
smaller RIN may be used if the max current is limited in
another way, such as with a Schottky diode across RSENSE
(Figure 3). This will reduce the high current measurement
accuracy by limiting the result, while increasing the low
current measurement resolution. This approach can be
helpful in cases where occasional large burst currents
may be ignored.
APPLICATIONS INFORMATION
the LTC6102, and into ROUT via the OUT pin. In order to
minimize gain error, –INS should be routed in a separate
path from –INF to a point as close to RIN as possible. In
addition, the higher potential terminal of RIN should be
connected directly to the positive terminal of RSENSE (or
any input voltage source). For the highest accuracy, RIN
should be a four-terminal resistor if it is less than 10Ω.
Selection of External Output Resistor, ROUT
The output resistor, ROUT, determines how the output cur-
rent is converted to voltage. VOUT is simply IOUT ROUT.
In choosing an output resistor, the max output voltage
must rst be considered. If the circuit that is driven by the
output does not have a limited input voltage, then ROUT
must be chosen such that the max output voltage does
not exceed the LTC6102 max output voltage rating. If the
following circuit is a buffer or ADC with limited input range,
then ROUT must be chosen so that IOUT(MAX) ROUT is less
than the allowed maximum input range of this circuit.
In addition, the output impedance is determined by ROUT. If
the circuit to be driven has high enough input impedance,
then almost any output impedance will be acceptable.
However, if the driven circuit has relatively low input imped-
ance, or draws spikes of current, such as an ADC might
do, then a lower ROUT value may be required in order to
preserve the accuracy of the output. As an example, if the
input impedance of the driven circuit is 100 times ROUT,
then the accuracy of VOUT will be reduced by 1% since:
VI
RR
OUT
IN DRIVEN
OUT
IN DRIVEN
=
+
=
()
IIR
IR
OUT
.
100
101
099
=
Error Sources
The current sense system uses an amplier and resistors
to apply gain and level shift the result. The output is then
dependent on the characteristics of the amplier, such as
gain and input offset, as well as resistor matching.
Figure 3. Shunt Diode Limits Maximum Input Voltage to Allow
Better Low Input Resolution Without Overranging
V+
LOAD
DSENSE
6102 F03
RSENSE
Care should be taken when designing the PC board lay-
out for RIN, especially for small RIN values. All trace and
interconnect impedances will increase the effective RIN
value, causing a gain error. It is important to note that the
large temperature drift of copper resistance will cause a
change in gain over temperature if proper care is not taken
to reduce this effect.
To further limit the effect of trace resistance on gain,
maximizing the accuracy of these circuits, the LTC6102 has
been designed with a Kelvin input. The inverting terminal
(–INS) is separate from the feedback path (–INF). During
operation, these two pins must be connected together.
The design of the LTC6102 is such that current into –INS
is input bias current only, which is typically 60pA at 25°C.
Almost all of the current from RIN ows into –INF, through
相关PDF资料 |
PDF描述 |
|---|---|
| 0459844323 | CONN RCPT R/A 4PWR 16SGL 1.57MM |
| LTC6252IS6#TRPBF | IC OPAMP R-R 720MHZ TSOT23-6 |
| 0459844322 | CONN RCPT R/A 4PWR 16SGL 2.36MM |
| 2060.0007.11 | FUSE 400MA 125V SMD FAST |
| 0459844321 | CONN RCPT R/A 4PWR 16SGL 3.18MM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6102CMS8#PBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LTC6102CMS8#TRPBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC6102CMS8-1#PBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LTC6102CMS8-1#TRPBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:2pA 电压 - 输入偏移:1000µV 电流 - 电源:85µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:剪切带 (CT) 产品目录页面:680 (CN2011-ZH PDF) 其它名称:MCP6L04T-E/SLCT |
| LTC6102CMS8PBF | 制造商:Linear Technology 功能描述:Zero-Drift curr Sense Amplifier LTC6102 |
发布紧急采购，3分钟左右您将得到回复。